Trims The Rivet Tip To Make Broken Ejector Spring Removal Simple
Hollow-end mill fits in drill press, spot faces the front rivet to take off just the peened area. Often lets you re-peen the existing rivet and eliminate rebluing the receiver.
Galons à la pointe de Rivet pour rendre cassé éjecteur printemps suppression Simple
Moulin de creux-fin s'inscrit dans la perceuse, place doit faire face le rivet avant de décoller juste la zone grenaillée. Souvent vous permet de re-ébavurer le rivet existant et d'éliminer les rebluing du récepteur.
Spécifications : arbre en acier, couteau en acier trempé. 2½"(6,3 cm) de long,. 31" (12.5 mm) arbre diamètre.. 143"(3,6 mm) diamètre de fraise.
Plus...
Évaluations client de BROWNELLS REMINGTON 870 EJECTOR SPRING RIVET CUTTER
Nombre d'évaluations: 1
De brownells.com: 1
Note moyenne: 5
Great investment!(10.02.2016)
This little rivet cutter made me save over $200 in gunsmithing work on my old 870 Wingmaster, which had been sitting in the gun safe for years because of a ''too-expensive-to-replace'' broken ejector spring. The instructions provided with the tool are very clear and allowed me, as indicated, to re-use the rivet to lock the new spring into the ejector. The only thing I did differently than prescribed by the instructions was to drive the rivet cutter down on the tiny rivet head by hand instead of using a press drill. The rivet cutter being very sharp and the rivet metal being very soft, I was afraid to ruin the rivet using a press drill. It took me 10 minutes to cut the rivet head slowly and safely by hand (clockwise twist of the fingers with little pressure).
Référence: 080000040 BROWNELLS REMINGTON 870 EJECTOR SPRING RIVET CUTTER050806103825 Moulin de creux-fin s'inscrit dans la perceuse, place doit faire face le rivet avant de décoller juste la zone grenaillée. Souvent vous permet de re-ébavurer le rivet existant et d'éliminer les rebluing du récepteur.
54.9CHF0CHF 54.90
*
En rupture de stock, délai de livraison d'environ 4-12 semaines depuis l'entrepôt des États-Unis.
Trims The Rivet Tip To Make Broken Ejector Spring Removal Simple
Hollow-end mill fits in drill press, spot faces the front rivet to take off just the peened area. Often lets you re-peen the existing rivet and eliminate rebluing the receiver.
Galons à la pointe de Rivet pour rendre cassé éjecteur printemps suppression Simple
Moulin de creux-fin s'inscrit dans la perceuse, place doit faire face le rivet avant de décoller juste la zone grenaillée. Souvent vous permet de re-ébavurer le rivet existant et d'éliminer les rebluing du récepteur.
Spécifications : arbre en acier, couteau en acier trempé. 2½"(6,3 cm) de long,. 31" (12.5 mm) arbre diamètre.. 143"(3,6 mm) diamètre de fraise.
Plus...
Évaluations client de BROWNELLS REMINGTON 870 EJECTOR SPRING RIVET CUTTER
Nombre d'évaluations: 1
De brownells.com: 1
Note moyenne: 5
Great investment!(10.02.2016)
This little rivet cutter made me save over $200 in gunsmithing work on my old 870 Wingmaster, which had been sitting in the gun safe for years because of a ''too-expensive-to-replace'' broken ejector spring. The instructions provided with the tool are very clear and allowed me, as indicated, to re-use the rivet to lock the new spring into the ejector. The only thing I did differently than prescribed by the instructions was to drive the rivet cutter down on the tiny rivet head by hand instead of using a press drill. The rivet cutter being very sharp and the rivet metal being very soft, I was afraid to ruin the rivet using a press drill. It took me 10 minutes to cut the rivet head slowly and safely by hand (clockwise twist of the fingers with little pressure).