Precisely aligns individual steel stamps to help ensure characters are straight and evenly spaced when stamping caliber designations on barrels. Allen head screws allow adjustment for accurate character spacing, so you get truly professional looking results. Machined port allows an unobstructed view of the first stamp head to ensure correct positioning on workpiece prior to tapping with your hammer. Accepts ¼" square stamps with 1/16", 3/32", or 1/8" character sizes. Fits barrels up to 1-3/8" diameter.
SPECS: Aluminum, natural finish with steel U-bolt and hardware. 2-3⁄8" (6cm) long x 3¼ (8.2cm) wide, 1½ (3.8cm) high.
Plus...
Pour l'alignement de précision lors du marquage de barils
Précisément aligne des timbres en acier individuels afin d'assurer des personnages sont directement et uniformément espacés lorsque l'estampillage des désignations de calibre sur fûts. Vis à tête Allen permettant l'ajustement d'espacement de caractères précis, afin que vous obteniez véritablement professionnel à la recherche de résultats. Port usinée permet une vue dégagée sur le premier chef de timbre afin d'assurer un positionnement correct sur la pièce avant taraudage avec votre marteau. Accepte ¼" timbres carrés avec des tailles de caractère 1/16", 3/32 po ou 1/8". Ajustements barils jusqu'à 1-3/8 po de diamètre.
Spécifications : aluminium, finition naturelle avec acier boulon en u et matériel. 2-3 ⁄ 8"(6cm) long x 3¼ (8,2 cm) de large, 1½ (3,8 cm) de haut.
Plus...
Évaluations client de LA BOUNTY STEEL STAMP GUIDE
Nombre d'évaluations: 2
De brownells.com: 2
Note moyenne: 1
Caution(08.01.2010)
The device is well made, however it will slip resulting in uneven markings. After reading the instructions over several times I tried it. I was disappointed with the results. I then tried it again on an old barrel and the same thing happened again. I made sure the holding ring was very tight. My opinion is save your maoney and go to a jeweler of plaque company that can do it right, the first time.
warning - disapointed(06.12.2012)
I was not able to get this device to work well even when following the directions. In the end, I was able to load several stamps in a row then tighten up the guide and clamp the assembly to a barrel. Even this way, it was hard to use. The clearance between the plates was too tight to insert the stamps without loosening the side screws. It is hard to get just five stamps into the guide (e.g., 300H&H cannot be done without the alignment risk of a second setup). I wish I had read keydiverfla's review before laying down my money.
Référence: 521104000 LA BOUNTY STEEL STAMP GUIDE Ref Fabricant: NONE Précisément aligne des timbres en acier individuels afin d'assurer des personnages sont directement et uniformément espacés lorsque l'estampillage des désignations de calibre sur fûts. Vis à tête Allen permettant l'ajustement d'espacement de caractères précis, afin que vous obteniez véritablement professionnel à la recherche de résultats. Port usinée permet une vue dégagée sur le premier chef de timbre afin d'assurer un positionnement correct sur la pièce avant taraudage avec votre marteau. Accepte ¼" timbres carrés avec des tailles de caractère 1/16", 3/32 po ou 1/8". Ajustements barils jusqu'à 1-3/8 po de diamètre.
69.9CHF3CHF 69.90
*
Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.
Precisely aligns individual steel stamps to help ensure characters are straight and evenly spaced when stamping caliber designations on barrels. Allen head screws allow adjustment for accurate character spacing, so you get truly professional looking results. Machined port allows an unobstructed view of the first stamp head to ensure correct positioning on workpiece prior to tapping with your hammer. Accepts ¼" square stamps with 1/16", 3/32", or 1/8" character sizes. Fits barrels up to 1-3/8" diameter.
SPECS: Aluminum, natural finish with steel U-bolt and hardware. 2-3⁄8" (6cm) long x 3¼ (8.2cm) wide, 1½ (3.8cm) high.
Plus...
Pour l'alignement de précision lors du marquage de barils
Précisément aligne des timbres en acier individuels afin d'assurer des personnages sont directement et uniformément espacés lorsque l'estampillage des désignations de calibre sur fûts. Vis à tête Allen permettant l'ajustement d'espacement de caractères précis, afin que vous obteniez véritablement professionnel à la recherche de résultats. Port usinée permet une vue dégagée sur le premier chef de timbre afin d'assurer un positionnement correct sur la pièce avant taraudage avec votre marteau. Accepte ¼" timbres carrés avec des tailles de caractère 1/16", 3/32 po ou 1/8". Ajustements barils jusqu'à 1-3/8 po de diamètre.
Spécifications : aluminium, finition naturelle avec acier boulon en u et matériel. 2-3 ⁄ 8"(6cm) long x 3¼ (8,2 cm) de large, 1½ (3,8 cm) de haut.
Plus...
Évaluations client de LA BOUNTY STEEL STAMP GUIDE
Nombre d'évaluations: 2
De brownells.com: 2
Note moyenne: 1
Caution(08.01.2010)
The device is well made, however it will slip resulting in uneven markings. After reading the instructions over several times I tried it. I was disappointed with the results. I then tried it again on an old barrel and the same thing happened again. I made sure the holding ring was very tight. My opinion is save your maoney and go to a jeweler of plaque company that can do it right, the first time.
warning - disapointed(06.12.2012)
I was not able to get this device to work well even when following the directions. In the end, I was able to load several stamps in a row then tighten up the guide and clamp the assembly to a barrel. Even this way, it was hard to use. The clearance between the plates was too tight to insert the stamps without loosening the side screws. It is hard to get just five stamps into the guide (e.g., 300H&H cannot be done without the alignment risk of a second setup). I wish I had read keydiverfla's review before laying down my money.