Increased pressure stabilizes the follower and improves feeding, especially on high-capacity magazines. SIG P220 provides 10% more power in your older .45 ACP Sig P220 and is the factory standard spring in newer P220s with a green recoil spring. Also fits the Browning BDA .45 ACP. Separate models available for magazines with a metal floorplate (MF) or a plastic floorplate (PF). Will not fit 8-round magazines made by Mec-Gar.
SPECS: Will not fit Meg-Gar Sig 220 magazines and 70873 fits Metal Floor plate Sig 220 and BDA magazines only, 79383 fits Plastic Floor plate Sig 220 magazines only.
Plus...
Meilleure alimentation pour votre semi-auto
Augmentation de la pression stabilise le suiveur et améliore l'alimentation, en particulier sur les magazines de grande capacité. SIG P220 fournit 10 % plus de puissance dans votre ancienne.45 ACP Sig P220 et le ressort standard usine dans P220s plus récents avec un ressort de recul vert. Convient également pour le Browning BDA.45 ACP. Modèles distincts disponibles pour les magazines avec une plaque de métal (MF) ou une plaque d'appui en plastique (PF). N'entre pas dans la ronde 8 magazines faites par Mec-Gar.
SPECS : ne rentre pas dans les magazines Meg-Gar Sig 220 et 70873 correspond à plancher métal plaque Sig 220 BDA magazines et seulement, 79383 correspond à des magazines de plaque Sig 220 plancher en plastique uniquement.
Plus...
Évaluations client de WOLFF +10% POWER SPRING, 3-PAK FITS SIG HI-CAP P226, P228, P229
Nombre d'évaluations: 3
De brownells.com: 3
Note moyenne: 3.7
Doesn't work correctly(08.09.2017)
Standard (factory) Sig P220 magazines have 6 coils at the top that are wound smaller to fit inside the follower when compressed, and then get bigger on the lower coils. These springs are large coils for the entire length, so when compressed they do not fit inside the follower. This means they stack up below the follower and end up being too tall, which means you can't get 8 rounds in the magazine no matter how hard you try.
My suggestion is buy the replacement springs for 10-round P220 mags (which DO) have the smaller coils on top, and trim them so they have the same number of coils are the factory 8-round springs. Thats what I ended up doing, works great.
Just what was needed!!!(16.09.2011)
I recently purchased a few Mec-Gar extended capacity mags for my Sig P226 .40 cal. Straight out of the box, I noticed the mag springs were not strong enough to lock the slide back after firing the last round. I ordered the Wolff +10% and they were exactly what was needed! I haven't had one single malfunction or the slide failing to lock back since. A great low cost solution!
Restores old Sig magazines(23.04.2015)
Bought These for an older Sig P226 9mm from 1989 that was given to me. The old springs were the factory original and they didn't have a lot of power left in them. The new springs took them back to feeling like new magazines and I could feel the difference right away while loading and firing. Nice for the slide to lock open again when I'm empty.
Référence: 969000057 WOLFF +10% POWER SPRING, 3-PAK FITS SIG HI-CAP P226, P228, P229 Ref Fabricant: 74373 Augmentation de la pression stabilise le suiveur et améliore l'alimentation, en particulier sur les magazines de grande capacité. SIG P220 fournit 10 % plus de puissance dans votre ancienne.45 ACP Sig P220 et le ressort standard usine dans P220s plus récents avec un ressort de recul vert. Convient également pour le Browning BDA.45 ACP. Modèles distincts disponibles pour les magazines avec une plaque de métal (MF) ou une plaque d'appui en plastique (PF). N'entre pas dans la ronde 8 magazines faites par Mec-Gar.
22.9CHF0CHF 22.90
*
En rupture de stock, délai de livraison d'environ 4-12 semaines depuis l'entrepôt des États-Unis.
Caractéristiques:Manufacture: Sig SauerModèle: Universal HandgunsQuantité: 3
Manufacture:
Sig Sauer
Modèle:
Universal Handguns
Quantité: 3 Poids du colis: 0.027kgHauteur d'expédition: 18mmLargeur d'expédition: 64mmLongueur d'expédition: 277mm
Détails de l'article
Fabriqué au USA
Référence: 969000220 WOLFF +10% POWER SPRING, 3-PAK FITS SIG P220/BROWNING BDA MF Ref Fabricant: 70873 Augmentation de la pression stabilise le suiveur et améliore l'alimentation, en particulier sur les magazines de grande capacité. SIG P220 fournit 10 % plus de puissance dans votre ancienne.45 ACP Sig P220 et le ressort standard usine dans P220s plus récents avec un ressort de recul vert. Convient également pour le Browning BDA.45 ACP. Modèles distincts disponibles pour les magazines avec une plaque de métal (MF) ou une plaque d'appui en plastique (PF). N'entre pas dans la ronde 8 magazines faites par Mec-Gar.
21.9CHF5CHF 21.90
*
Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.
Caractéristiques:Manufacture: Sig SauerModèle: P220Quantité: 3
Increased pressure stabilizes the follower and improves feeding, especially on high-capacity magazines. SIG P220 provides 10% more power in your older .45 ACP Sig P220 and is the factory standard spring in newer P220s with a green recoil spring. Also fits the Browning BDA .45 ACP. Separate models available for magazines with a metal floorplate (MF) or a plastic floorplate (PF). Will not fit 8-round magazines made by Mec-Gar.
SPECS: Will not fit Meg-Gar Sig 220 magazines and 70873 fits Metal Floor plate Sig 220 and BDA magazines only, 79383 fits Plastic Floor plate Sig 220 magazines only.
Plus...
Meilleure alimentation pour votre semi-auto
Augmentation de la pression stabilise le suiveur et améliore l'alimentation, en particulier sur les magazines de grande capacité. SIG P220 fournit 10 % plus de puissance dans votre ancienne.45 ACP Sig P220 et le ressort standard usine dans P220s plus récents avec un ressort de recul vert. Convient également pour le Browning BDA.45 ACP. Modèles distincts disponibles pour les magazines avec une plaque de métal (MF) ou une plaque d'appui en plastique (PF). N'entre pas dans la ronde 8 magazines faites par Mec-Gar.
SPECS : ne rentre pas dans les magazines Meg-Gar Sig 220 et 70873 correspond à plancher métal plaque Sig 220 BDA magazines et seulement, 79383 correspond à des magazines de plaque Sig 220 plancher en plastique uniquement.
Plus...
Évaluations client de WOLFF +10% POWER SPRING, 3-PAK FITS SIG HI-CAP P226, P228, P229
Nombre d'évaluations: 3
De brownells.com: 3
Note moyenne: 3.7
Doesn't work correctly(08.09.2017)
Standard (factory) Sig P220 magazines have 6 coils at the top that are wound smaller to fit inside the follower when compressed, and then get bigger on the lower coils. These springs are large coils for the entire length, so when compressed they do not fit inside the follower. This means they stack up below the follower and end up being too tall, which means you can't get 8 rounds in the magazine no matter how hard you try.
My suggestion is buy the replacement springs for 10-round P220 mags (which DO) have the smaller coils on top, and trim them so they have the same number of coils are the factory 8-round springs. Thats what I ended up doing, works great.
Just what was needed!!!(16.09.2011)
I recently purchased a few Mec-Gar extended capacity mags for my Sig P226 .40 cal. Straight out of the box, I noticed the mag springs were not strong enough to lock the slide back after firing the last round. I ordered the Wolff +10% and they were exactly what was needed! I haven't had one single malfunction or the slide failing to lock back since. A great low cost solution!
Restores old Sig magazines(23.04.2015)
Bought These for an older Sig P226 9mm from 1989 that was given to me. The old springs were the factory original and they didn't have a lot of power left in them. The new springs took them back to feeling like new magazines and I could feel the difference right away while loading and firing. Nice for the slide to lock open again when I'm empty.