Votre panier est vide.

Panier

SEEKINS PRECISION
AR-15/M16 ENHANCED BOLT CATCH

811452029613 100011243

Enables Easy Locking & Fast Bolt Release

Steel bolt catch features an enlarged lower portion that makes it easy to lock bolt to the rear. Enlarged upper portion allows fast bolt release, and “Diamond Texture” thumb pad gives positive engagement and enhances rifle’s appearance.

SPECS: Steel, Parkerized. 1-3/16" (3cm) long. Fits all standard AR-15s.

Plus...

Permet facile verrouillage & rapide dégagement de boulon

Boulon en acier catch caractéristiques une portion agrandie de basse qui le rend facile à verrouillage vis à l'arrière. Partie supérieure élargie permet de s'échapper rapidement boulon, et « Diamond Texture » pouce pad donne un engagement positif et améliore l'apparence du fusil.

Spécifications : acier, Parkerized. 1-3/16 po (3cm) long. S'adapte à tous les standards AR-15 s.

Plus...

Évaluations client de SEEKINS PRECISION AR15 BOLT CATCH

Nombre d'évaluations: 9
De brownells.com: 9
Note moyenne: 2.9

Big upgrade over the stock part (20.05.2014)

I was drawn to this part because I found the bottom portion of a standard bolt catch to be inadequate when locking the bolt open. The enlarged and protruded bottom portion of this part solved that problem for me. It is machined well and of high quality. The only reason I did not give it 5 stars is because it is incompatible with the Magpul BAD lever or any equivalent device that attaches to a standard bolt release. This may or may not matter to you.

Easy Install, Easy Upgrade: Faster Bolt (21.06.2014)

Used for a RRA Entry Tactical Duty Rifle.
This simple upgrade makes it faster & easier to lock back and release the BCG.
No Qualms Here
Buy It! you wont regret it!

Will NOT work in Mega Side-Charging Upr (21.06.2014)

While this is a lovely bolt catch, it will NOT work in a Mega Arms Side-Charging Upper. There is not enough material milled out of the upper for this bolt catch to fit.

Out of spec (24.09.2014)

I have tried two of the Seekins enhanced bolt catch on different builds without success.

The first one would not lock the bolt open after firing the last round from several different magazines, and would not hold the bolt back even when manually locked back.

The second one I ordered would not fit into the receiver at all. It was a Seekins forged lower that I was building up. I measured both the lower and the bolt catch and the bolt catch was slightly oversized to the point that it would not fit.

I really like the design of the larger paddle, but they need to get their specs correct on this part.

Out of Spec Hole Diameter (23.11.2014)

I bought one of these about a year ago for the AR 15 that I was building and it worked perfectly. I decided to buy two more for my other AR's but they are both defective. The hole diameter is too small and they will not work freely. The hole diameter is the same size as the roll pin when it should be slightly larger. When I compared the hole sizes to the old bolt catch their is a very noticeable difference. I am guessing that they ran a whole batch of these with the wrong hole size and from the other review that I read Seekins Precision does not QA their parts! I think they need to remove the name "Precision" from their name since they say they make MIL SPEC parts when their parts aren't!

Didn't work for me (02.02.2015)

I've build around 11 ARs using Aero, Spikes, DPMS, Bushmaster and other lowers for myself and a few friends. I've always used the bolt catch from DPMS or CMMG lpk. On my last AR build (Aero lower) for myself I decided to put this item in for a more enhanced bolt catch. I wanted one bigger in both the catch and release areas.

Installation was like any bolt catch. It moved freely without the mag and it locked the bolt without the mag but when the mag came into play, it never locked itself. It seemed like it had problems moving, it felt tight with the mag in the mag well.

It looks good, good material, nice wide surface on both ends but not in spec.

Great upgrade (17.03.2016)

After my first carbine class I went in search of a bolt catch that had an enlarged bottom portion for locking the bolt open.

I found the Seekins and gave it a try. It worked perfectly and was exactly what I was looking for. Since then I've installed them in three other lowers and have had no problems with fit or function.

I've installed them in lowers from BCM, Spikes Tactical, and PSA.

No go (22.12.2016)

Love the feel of this catch, couldn't care about looks. I wanted a larger paddle and In return the bolt won't lock up on the last round. Happened after two months. I don't feel you should have to remove the paddle to clean it inside of 10000 rounds. And I find it funny that the stock catch never wore down on my service rifle.

Best uses..."target practice" only because this will make you one. Save your money and go stock!

Bent and locked up my 9mm carbine (30.07.2018)

I've run a few of these before without issue, but on the FIRST time I ran my 9mm carbine to slide-lock it bent this piece and locked up my PCC HARD. I had to use a screwdriver and a hammer to bend it back enough to tap it down. I could then slide my bolt forward and begin to repair. I had been using a box-stock factory bolt catch without issue prior to this. Not an upgrade and too soft. The one I had on my HD rifle is now coming off as well and replaced with something hardened.

Lire 9 plus d'avis sur brownells.com

36.9 36.9 1 CHF

Référence: 100011243
SEEKINS PRECISION AR15 BOLT CATCH
Ref Fabricant: 011510057 811452029613 Boulon en acier catch caractéristiques une portion agrandie de basse qui le rend facile à verrouillage vis à l'arrière. Partie supérieure élargie permet de s'échapper rapidement boulon, et « Diamond Texture » pouce pad donne un engagement positif et améliore l'apparence du fusil.

36.9 CHF 8 CHF 36.90 *

Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.

Caractéristiques: Manufacture: AR-15

Ajouter à la Liste d'Envies

Poser un question

Propriétés

Ajouter à la Liste d'Envies

Poser un question

Caractéristiques

Manufacture: AR-15 Poids du colis: 0.045kg Hauteur d'expédition: 25mm Largeur d'expédition: 69mm Longueur d'expédition: 198mm

Détails de l'article

Fabriqué au USA
US export classification: 0A501.x

Enables Easy Locking & Fast Bolt Release

SPECS: Steel, Parkerized. 1-3/16" (3cm) long. Fits all standard AR-15s.

Plus...

Permet facile verrouillage & rapide dégagement de boulon

Spécifications : acier, Parkerized. 1-3/16 po (3cm) long. S'adapte à tous les standards AR-15 s.

Plus...

Évaluations client de SEEKINS PRECISION AR15 BOLT CATCH

Nombre d'évaluations: 9
De brownells.com: 9
Note moyenne: 2.9

Big upgrade over the stock part (20.05.2014)

Easy Install, Easy Upgrade: Faster Bolt (21.06.2014)

Used for a RRA Entry Tactical Duty Rifle.
This simple upgrade makes it faster & easier to lock back and release the BCG.
No Qualms Here
Buy It! you wont regret it!

Will NOT work in Mega Side-Charging Upr (21.06.2014)

While this is a lovely bolt catch, it will NOT work in a Mega Arms Side-Charging Upper. There is not enough material milled out of the upper for this bolt catch to fit.

Out of spec (24.09.2014)

Out of Spec Hole Diameter (23.11.2014)

Didn't work for me (02.02.2015)

Great upgrade (17.03.2016)

No go (22.12.2016)

Bent and locked up my 9mm carbine (30.07.2018)

Lire 9 plus d'avis sur brownells.com

Poursuivre vos achats

SEEKINS PRECISION SAFETY SELECTOR KIT, AMBIDEXTROUS, BLACK
SAFETY SELECTOR KIT, AMBIDEXTROUS, BLACK

SEEKINS PRECISION

En stock

CHF 89.90 *

Sécurités

3.5

SEEKINS PRECISION AR-15 BILLET MAGAZINE RELEASE BUTTON
AR-15/M16 BILLET MAGAZINE RELEASE BUTTON

SEEKINS PRECISION

Récommandé

CHF 19.90 *

Verrous de magasin

TROY INDUSTRIES AMBIDEXTROUS MAGAZINE RELEASE
AR-15/M16 AMBIDEXTROUS MAGAZINE RELEASE

TROY INDUSTRIES

En stock

CHF 99.90 *

Verrous de magasin

4.2

ISMI 18 LB. SPRING GLOCK® 19
FLAT WIRE RECOIL SPRINGS FOR GLOCK®

ISMI

En stock

CHF 16.90 *

Ressorts Anti-Recul

HARFORD ENGRAVING SERVICES AR-15 "DON'T TREAD ON ME"/U.S. FLAG
AR-15/M16 ENGRAVED EJECTION PORT COVERS

HARFORD ENGRAVING SERVICES

Non disponible

CHF 15.90 *

Clapets Trappe d'Ejection

4.4

Connexion

Mot de passe oublié ?
S'inscrire

SOCIAL MEDIA

Facebook

BROWNELLS.CH

CATÉGORIES

COMMANDER

SERVICE CLIENTÈLE

Bienvenue!

Bienvenue sur brownells.ch, le plus grand fournisseur d'accessoires pour armes à feu, Pièces détachées et Outils armurier en Suisse!

Notre garantie - Votre satisfaction

Si vous aimez tirer, travailler sur les armes en tant que professionnel ou pour votre loisir, ou bien simplement posséder une arme à feu, brownells.fr est fait pour vous! Depuis plus de 75 ans, tireurs, armuriers professionnels, amateurs, militaires / armuriers des forces de l'ordre ou encore as du bricolage d'armes à feu se sont tournés vers brownells.ch pour s'approvisionner en pièces et fournitures de haute qualité dont ils ont besoin.

Vous trouverez plus de 50.000 produits, y compris des pièces détachées uniques d'armes à feu, des accessoires, des outils d'armuriers, des munitions et bien d'autres produits pour entretenir, réparer et mettre à niveau vos armes.professionnels, amateurs, militaires / armuriers des forces de l'ordre ou encore as du bricolage d'armes à feu se sont tournés vers brownells.ch pour s'approvisionner en pièces et fournitures de haute qualité dont ils ont besoin.