Brownells Svizzera - Il più grande rivenditore di componenti e accessori per armi ed attrezzistica per armieri Suisse / Schweiz

BROWNELLS
CERROSAFE® CHAMBER CASTING ALLOY

080027100
Never Wears Out- Use Over And Over
There are various products on the market which can be used to make a cast of a gun chamber. To be certain that the product we are offering you is the best and most practical, we contacted the basic manufacturer. They recommended Cerrosafe because of its unique features. Unlike Woodsmetal which swells upon cooling and cannot be removed from a gun chamber, Cerrosafe shrinks during the first 30 minutes of cooling and then at the end of an hour, is EXACTLY chamber size. At the end of 200 hours it will have expanded approximately .0025". This factor is well known by all toolmakers and they will take it into consideration when making dies or reamers or gauges from your cast - if you will tell them the cast is of Cerrosafe. Cerrosafe melts between 158° - 190° F. It should be melted in a clean, iron ladle. Source of heat should be removed as soon as the alloy is completely melted, at which time it is ready to pour. The solidified casting should be removed from the chamber before, or when, it cools to room temperature. If allowed to remain in the mold over an hour, it will grip the chamber walls and be difficult to remove. Clean the chamber of the rifle thoroughly, then plug the bore immediately ahead of the throat with a small rag - but not so tightly it cannot be driven out. If possible, pour the molten Cerrosafe through a small tube into the bottom of the cast, gradually removing the tube as the chamber fills. If the barrel is cold, warm it to room temperature or above before making the cast. When cooled, remove from chamber, using a rod or dowel from the muzzle end of the gun.
SPECS: Sold by weight. Alloy. Infinitely reusable.
26.9 46.9 2 CHF
N. prodotto: 080027100
BROWNELLS CERROSAFE CHAMBER CASTING ALLOY 1LB Ci sono vari prodotti sul mercato che può essere usato per fare un cast di una camera di pistola. Per essere certi che il prodotto che vi stiamo offrendo è la migliore e più pratico, abbiamo contattato il produttore di base. Hanno consigliato Cerrosafe a causa delle sue caratteristiche uniche. A differenza di Woodsmetal che si gonfia sul raffreddamento e non può essere rimosso da una camera di pistola, si restringe Cerrosafe durante i primi 30 minuti di raffreddamento e poi alla fine di un'ora, è esattamente camera dimensioni. Alla fine di 200 ore sarà hanno ampliato circa. 0025". Questo fattore è noto da tutti attrezzisti e lo prenderanno in considerazione quando si effettua il dies o alesatori o calibri da ingessatura - se dirà loro che il cast è di Cerrosafe. Cerrosafe si scioglie tra 158° - 190° F. Esso deve essere sciolto in un mestolo di ferro pulito. Fonte di calore deve essere rimosso non appena la lega è completamente fuso, a che ora è pronto a versare. Il casting solidificato dovrebbe essere rimosso dalla camera prima, o quando si raffredda a temperatura ambiente. Se autorizzati a rimanere nello stampo più di un'ora, sarà presa le pareti della camera e difficile da rimuovere. Pulire accuratamente la camera del fucile, quindi collegare il foro immediatamente davanti alla gola con un piccolo straccio - ma non così strettamente non può essere cacciato. Se possibile, versare sul fondo del cast, il fuso Cerrosafe attraverso un piccolo tubo gradualmente rimuovere il tubo come la camera riempie. Se la canna è fredda, scaldarlo a temperatura ambiente o superiore prima di fare il cast. Quando raffreddato, togliere dalla camera, utilizzando una canna o un tassello da fine museruola della pistola.
46.9 CHF 126 CHF 46.90 *
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.

Caratteristiche

Peso della spedizione: 0.454kg Altezza di spedizione: 8mm Larghezza di spedizione: 76mm Lunghezza di spedizione: 226mm

Dettagli dell'elemento

Made in Usa



N. prodotto: 080027050
BROWNELLS CERROSAFE CHAMBER CASTING ALLOY 1/2LB Ci sono vari prodotti sul mercato che può essere usato per fare un cast di una camera di pistola. Per essere certi che il prodotto che vi stiamo offrendo è la migliore e più pratico, abbiamo contattato il produttore di base. Hanno consigliato Cerrosafe a causa delle sue caratteristiche uniche. A differenza di Woodsmetal che si gonfia sul raffreddamento e non può essere rimosso da una camera di pistola, si restringe Cerrosafe durante i primi 30 minuti di raffreddamento e poi alla fine di un'ora, è esattamente camera dimensioni. Alla fine di 200 ore sarà hanno ampliato circa. 0025". Questo fattore è noto da tutti attrezzisti e lo prenderanno in considerazione quando si effettua il dies o alesatori o calibri da ingessatura - se dirà loro che il cast è di Cerrosafe. Cerrosafe si scioglie tra 158° - 190° F. Esso deve essere sciolto in un mestolo di ferro pulito. Fonte di calore deve essere rimosso non appena la lega è completamente fuso, a che ora è pronto a versare. Il casting solidificato dovrebbe essere rimosso dalla camera prima, o quando si raffredda a temperatura ambiente. Se autorizzati a rimanere nello stampo più di un'ora, sarà presa le pareti della camera e difficile da rimuovere. Pulire accuratamente la camera del fucile, quindi collegare il foro immediatamente davanti alla gola con un piccolo straccio - ma non così strettamente non può essere cacciato. Se possibile, versare sul fondo del cast, il fuso Cerrosafe attraverso un piccolo tubo gradualmente rimuovere il tubo come la camera riempie. Se la canna è fredda, scaldarlo a temperatura ambiente o superiore prima di fare il cast. Quando raffreddato, togliere dalla camera, utilizzando una canna o un tassello da fine museruola della pistola.
26.9 CHF 79 CHF 26.90 *
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
Never Wears Out- Use Over And Over
There are various products on the market which can be used to make a cast of a gun chamber. To be certain that the product we are offering you is the best and most practical, we contacted the basic manufacturer. They recommended Cerrosafe because of its unique features. Unlike Woodsmetal which swells upon cooling and cannot be removed from a gun chamber, Cerrosafe shrinks during the first 30 minutes of cooling and then at the end of an hour, is EXACTLY chamber size. At the end of 200 hours it will have expanded approximately .0025". This factor is well known by all toolmakers and they will take it into consideration when making dies or reamers or gauges from your cast - if you will tell them the cast is of Cerrosafe. Cerrosafe melts between 158° - 190° F. It should be melted in a clean, iron ladle. Source of heat should be removed as soon as the alloy is completely melted, at which time it is ready to pour. The solidified casting should be removed from the chamber before, or when, it cools to room temperature. If allowed to remain in the mold over an hour, it will grip the chamber walls and be difficult to remove. Clean the chamber of the rifle thoroughly, then plug the bore immediately ahead of the throat with a small rag - but not so tightly it cannot be driven out. If possible, pour the molten Cerrosafe through a small tube into the bottom of the cast, gradually removing the tube as the chamber fills. If the barrel is cold, warm it to room temperature or above before making the cast. When cooled, remove from chamber, using a rod or dowel from the muzzle end of the gun.
SPECS: Sold by weight. Alloy. Infinitely reusable.
Newsletter