Drop-in replacement follower for USGI 30-round magazines won’t tilt, so it helps prevent jams, misfeeds, and other magazine-related failures. Rectangular extensions at the front and rear prevent tilt of the round stack to eliminate jams caused by over-compression and binding of the spring. Self-lubricating polymer composition helps ensure smooth movement for easier loading and ultra-smooth feeding. Extended bolt catch makes sure bolt locks open after the last round is fired. A spring stabilizer molded into the underside keeps spring force centered no matter how many rounds are in the mag, rounded edges on the extensions for even slicker movement in the mag body, and more streamlined ramp geometry for easier travel of the round from the magazine into the chamber.
SPECS: Molded polymer, Yellow. Fits standard 30-round magazine. Instructions included. Sold in 3-paks.
Altro...
Non inclinare; Alimenta i turni senza intoppi; Aiuta a previene guasti relativi Magazine
Seguace di ricambio drop-in per riviste USGI 30 colpi non inclina, quindi aiuta a prevenire inceppamenti, inceppamento e altri problemi correlati a rivista. Estensioni rettangolare nella parte anteriore e posteriore prevenire inclinazione dello stack rotondo per eliminare inceppamenti causati da eccessiva compressione e associazione della primavera. Autolubrificanti composizione del polimero consente di garantire la fluidità di movimento per caricamento più facile e alimentazione ultra-liscia. Cattura bullone estesa assicura bullone aperta dopo l'ultimo round si è sparato. Uno stabilizzatore di primavera stampato nel lato inferiore mantiene centrata non importa quanti colpi sono nella mag, bordi arrotondati sulle estensioni per il movimento anche slicker nel corpo mag, forza della molla e più snello geometria di rampa per il viaggio più facile del turno dalla rivista nella camera.
Specifiche: polimero stampato, giallo. Misure standard 30-round magazine. Istruzioni incluse. Venduto in 3-paks.
Altro...
Punteggi dei clienti per MAGPUL ENHANCED SELF-LEVELING FOLLOWER 3-PAK, YELLOW
Numero di punteggi: 4
Da brownells.com: 4
Punteggio medio: 4.5
work great and look nice(25.05.2012)
i run them through all my ars. work great! doesnt tilt at all when loading. and function great. no issues so far
Best follower made for the AR15/M16(13.01.2014)
While these may be tricky to install in some magazines due to the placement of the little tabs on the bottom of the magazine that hold the floor plate in place because some manufacturers have them in slightly different locations, they are drop in fit for Colt brand mags but can be fitted to work with all metal magazines with some effort.
But the followers are the best available and function better than both the old style black and green followers.
If you own any metal mags that do not have magpul followers, these are one of the best and most cost efficient upgrades that actually enhance performance that you can buy.
DO NOT REPLACE TAN FOLLOWERS(08.10.2017)
I have some newer issue Army mags with the tan follower. In them, the spring attachment point to the followers is different. The proprietary spring in these GI mags will cause the magpul followers to tilt and snag HARD(needed screwdrivers to correct it)exactly like the old green followers used to. I tried all three followers from the pack in multiple NEW issued magazines with the tan followers, and the results were identicle. ONLY purchase for mags without the tan USGI follower
Turn Old Mags New For a Few Dollars(21.10.2017)
I had 15 steel G.I. style AR mags sitting in my closet for years that I never used. They were extras I had accumulated during my Army years. They were tossed aside because they did not have self-leveling followers and old, weak springs (not a good thing when feeding the rifle your life depended on). After cleaning lots of powder and sand out of the mag bodies I installed Magpull Self-Leveling followers and Brownell's springs in each. That's about 5$ or less to turn a magazine that was shelved due to constant feeding issues into a new magazine. It's very cost effective compared to buying the same quantity of new magazines. Be sure to inspect the magazine's feed lips, as a metal magazine's are more susceptible to them bending and causing issues. Use a can of spray paint and paint them to your liking and you've got a lifetime's supply of mags that you can throw a new spring into when appropriate. I saw one reviewer comment that there was a fitment issue with the follower to the spring, I bought 15 of the followers and 15 springs and had no such issue. The magazine spring needs to bent slightly at its end to fit into the follower's spring hold and you are good to go.
N. prodotto: 100009896 MAGPUL ENHANCED SELF-LEVELING FOLLOWER 3-PAK, YELLOW Parti Fabbricante: MAG110-YEL873750000374 Seguace di ricambio drop-in per riviste USGI 30 colpi non inclina, quindi aiuta a prevenire inceppamenti, inceppamento e altri problemi correlati a rivista. Estensioni rettangolare nella parte anteriore e posteriore prevenire inclinazione dello stack rotondo per eliminare inceppamenti causati da eccessiva compressione e associazione della primavera. Autolubrificanti composizione del polimero consente di garantire la fluidità di movimento per caricamento più facile e alimentazione ultra-liscia. Cattura bullone estesa assicura bullone aperta dopo l'ultimo round si è sparato. Uno stabilizzatore di primavera stampato nel lato inferiore mantiene centrata non importa quanti colpi sono nella mag, bordi arrotondati sulle estensioni per il movimento anche slicker nel corpo mag, forza della molla e più snello geometria di rampa per il viaggio più facile del turno dalla rivista nella camera.
13.9CHF752CHF 13.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
Drop-in replacement follower for USGI 30-round magazines won’t tilt, so it helps prevent jams, misfeeds, and other magazine-related failures. Rectangular extensions at the front and rear prevent tilt of the round stack to eliminate jams caused by over-compression and binding of the spring. Self-lubricating polymer composition helps ensure smooth movement for easier loading and ultra-smooth feeding. Extended bolt catch makes sure bolt locks open after the last round is fired. A spring stabilizer molded into the underside keeps spring force centered no matter how many rounds are in the mag, rounded edges on the extensions for even slicker movement in the mag body, and more streamlined ramp geometry for easier travel of the round from the magazine into the chamber.
SPECS: Molded polymer, Yellow. Fits standard 30-round magazine. Instructions included. Sold in 3-paks.
Altro...
Non inclinare; Alimenta i turni senza intoppi; Aiuta a previene guasti relativi Magazine
Seguace di ricambio drop-in per riviste USGI 30 colpi non inclina, quindi aiuta a prevenire inceppamenti, inceppamento e altri problemi correlati a rivista. Estensioni rettangolare nella parte anteriore e posteriore prevenire inclinazione dello stack rotondo per eliminare inceppamenti causati da eccessiva compressione e associazione della primavera. Autolubrificanti composizione del polimero consente di garantire la fluidità di movimento per caricamento più facile e alimentazione ultra-liscia. Cattura bullone estesa assicura bullone aperta dopo l'ultimo round si è sparato. Uno stabilizzatore di primavera stampato nel lato inferiore mantiene centrata non importa quanti colpi sono nella mag, bordi arrotondati sulle estensioni per il movimento anche slicker nel corpo mag, forza della molla e più snello geometria di rampa per il viaggio più facile del turno dalla rivista nella camera.
Specifiche: polimero stampato, giallo. Misure standard 30-round magazine. Istruzioni incluse. Venduto in 3-paks.
Altro...
Punteggi dei clienti per MAGPUL ENHANCED SELF-LEVELING FOLLOWER 3-PAK, YELLOW
Numero di punteggi: 4
Da brownells.com: 4
Punteggio medio: 4.5
work great and look nice(25.05.2012)
i run them through all my ars. work great! doesnt tilt at all when loading. and function great. no issues so far
Best follower made for the AR15/M16(13.01.2014)
While these may be tricky to install in some magazines due to the placement of the little tabs on the bottom of the magazine that hold the floor plate in place because some manufacturers have them in slightly different locations, they are drop in fit for Colt brand mags but can be fitted to work with all metal magazines with some effort.
But the followers are the best available and function better than both the old style black and green followers.
If you own any metal mags that do not have magpul followers, these are one of the best and most cost efficient upgrades that actually enhance performance that you can buy.
DO NOT REPLACE TAN FOLLOWERS(08.10.2017)
I have some newer issue Army mags with the tan follower. In them, the spring attachment point to the followers is different. The proprietary spring in these GI mags will cause the magpul followers to tilt and snag HARD(needed screwdrivers to correct it)exactly like the old green followers used to. I tried all three followers from the pack in multiple NEW issued magazines with the tan followers, and the results were identicle. ONLY purchase for mags without the tan USGI follower
Turn Old Mags New For a Few Dollars(21.10.2017)
I had 15 steel G.I. style AR mags sitting in my closet for years that I never used. They were extras I had accumulated during my Army years. They were tossed aside because they did not have self-leveling followers and old, weak springs (not a good thing when feeding the rifle your life depended on). After cleaning lots of powder and sand out of the mag bodies I installed Magpull Self-Leveling followers and Brownell's springs in each. That's about 5$ or less to turn a magazine that was shelved due to constant feeding issues into a new magazine. It's very cost effective compared to buying the same quantity of new magazines. Be sure to inspect the magazine's feed lips, as a metal magazine's are more susceptible to them bending and causing issues. Use a can of spray paint and paint them to your liking and you've got a lifetime's supply of mags that you can throw a new spring into when appropriate. I saw one reviewer comment that there was a fitment issue with the follower to the spring, I bought 15 of the followers and 15 springs and had no such issue. The magazine spring needs to bent slightly at its end to fit into the follower's spring hold and you are good to go.