No Lathe Needed, No Need To Remove Barrel From Frame
Super gentle angle as currently used by Ruger on their .38/.357 DA guns. If you set back a Ruger barrel or just want to duplicate this angle on any other barrel, use this cutter. You CANNOT use 18° or 11° cutters on a 5° throat without exceeding maximum throat diameter or making a compound angle.
Plus...
Aucun tour ne nécessaire, pas besoin de sortir le barillet du palier
Angle super douce tel qu'il est utilisé par Ruger sur leurs armes à feu.38/.357 DA. Si vous en retrait un baril de Ruger, ou tout simplement de reproduire cet angle sur n'importe quel autre Canon, utiliser cette coupe. Vous ne pouvez pas utiliser 18° ou 11° coupe sur une gorge 5° sans excédant le diamètre maximal ou formant un angle composé.
Plus...
Évaluations client de BROWNELLS 5 CHAMFER CUTTER FOR .44-.45 CALIBER
Nombre d'évaluations: 2
De brownells.com: 2
Note moyenne: 1
My 45 cal, 5 Degree Did Not Cut.(15.05.2014)
I tried this 5 degree cutter to cut forcing cone of my 45 LC Blackhawk. Cutter chipped and dulled quickly. I returned cutter for refund. I had to clean up damage caused by 5 degree cutter using their 10 degree cutter. Forcing cone is now oversize and 10 degrees. Thank You Brownells
Failed to cut - damaged the barrel(16.11.2017)
Just as Keith Sharp said in his review, this cutter would not cut at all. It did, however, damage the barrel. I read some literature from a rental outfit that says that these are high speed steel and that this "may not" cut newer stainless steel barrels that can be ultra hard.
Brownell's needs to look into this. If the cutters are defective, find another source. If the cutters will not cut modern stainless, the ad should say that. This issue cannot be left alone.
Référence: 080486500 BROWNELLS 5 CHAMFER CUTTER FOR .44-.45 CALIBER Angle super douce tel qu'il est utilisé par Ruger sur leurs armes à feu.38/.357 DA. Si vous en retrait un baril de Ruger, ou tout simplement de reproduire cet angle sur n'importe quel autre Canon, utiliser cette coupe. Vous ne pouvez pas utiliser 18° ou 11° coupe sur une gorge 5° sans excédant le diamètre maximal ou formant un angle composé.
69.9CHF5CHF 69.90
*
Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.
Référence: 080486100 BROWNELLS 5 CHAMFER CUTTER FOR .38 CALIBER Angle super douce tel qu'il est utilisé par Ruger sur leurs armes à feu.38/.357 DA. Si vous en retrait un baril de Ruger, ou tout simplement de reproduire cet angle sur n'importe quel autre Canon, utiliser cette coupe. Vous ne pouvez pas utiliser 18° ou 11° coupe sur une gorge 5° sans excédant le diamètre maximal ou formant un angle composé.
59.9CHF0CHF 59.90
*
En rupture de stock, délai de livraison d'environ 4-12 semaines depuis l'entrepôt des États-Unis.
Caractéristiques:Calibre: 38/357 Caliber (.357-.359)Degré: 5 DegreesManufacture: Universel Arme de Poing
No Lathe Needed, No Need To Remove Barrel From Frame
Super gentle angle as currently used by Ruger on their .38/.357 DA guns. If you set back a Ruger barrel or just want to duplicate this angle on any other barrel, use this cutter. You CANNOT use 18° or 11° cutters on a 5° throat without exceeding maximum throat diameter or making a compound angle.
Plus...
Aucun tour ne nécessaire, pas besoin de sortir le barillet du palier
Angle super douce tel qu'il est utilisé par Ruger sur leurs armes à feu.38/.357 DA. Si vous en retrait un baril de Ruger, ou tout simplement de reproduire cet angle sur n'importe quel autre Canon, utiliser cette coupe. Vous ne pouvez pas utiliser 18° ou 11° coupe sur une gorge 5° sans excédant le diamètre maximal ou formant un angle composé.
Plus...
Évaluations client de BROWNELLS 5 CHAMFER CUTTER FOR .44-.45 CALIBER
Nombre d'évaluations: 2
De brownells.com: 2
Note moyenne: 1
My 45 cal, 5 Degree Did Not Cut.(15.05.2014)
I tried this 5 degree cutter to cut forcing cone of my 45 LC Blackhawk. Cutter chipped and dulled quickly. I returned cutter for refund. I had to clean up damage caused by 5 degree cutter using their 10 degree cutter. Forcing cone is now oversize and 10 degrees. Thank You Brownells
Failed to cut - damaged the barrel(16.11.2017)
Just as Keith Sharp said in his review, this cutter would not cut at all. It did, however, damage the barrel. I read some literature from a rental outfit that says that these are high speed steel and that this "may not" cut newer stainless steel barrels that can be ultra hard.
Brownell's needs to look into this. If the cutters are defective, find another source. If the cutters will not cut modern stainless, the ad should say that. This issue cannot be left alone.