Reduces Pull Weight For A Light, Crisp Trigger Pull
Competition trigger pull spring kits reduce the pull weight of heavy factory triggers by approximately 2½ lbs. for a much improved trigger pull and better accuracy. #25A fits all pre-’91 Browning Hi-Power pistols, and includes (1) 22 lb. hammer spring, (1) reduced power trigger return spring, and (1) reduced power firing pin spring. #25B fits 1991 and later Hi-Power pistols, and includes (1) 22 lb. hammer spring and (1) reduced power firing pin spring.
SPECS: Spring steel. #25A includes (3) springs. #25B include (2) springs.
Altro...
Riduce il peso di tirare per un tiro di innesco leggero, croccante
Kit molla di concorrenza trigger pull ridurre il peso di tirare di trigger fabbrica pesante circa 2½ libbre per un grilletto molto migliorato tirare e migliore precisione. #25A si adatta a tutte le pistole Browning Hi-Power di pre - 91, primavera del martello (1) 22 lb, (1) potenza ridotta innescare molla e molla percussore (1) potenza ridotta. #25B adatta pistole 1991 e successivamente Hi-Power e comprende (1) 22 lb martello molla e molla percussore (1) potenza ridotta.
Punteggi dei clienti per CYLINDER & SLIDE #25-A SPRING KIT
Numero di punteggi: 4
Da brownells.com: 4
Punteggio medio: 3.3
Misleading(31.05.2012)
I installed these springs on a new BHP MK3 which originally measured 9.25 lbs at the trigger. After installation the trigger measured 9.25 lbs. The hammer spring was 4 coils longer than the stock or another manutacturer's replacement springs. This means you either have to cut the coils or pre-load the spring extensively to install it on the strut. So unless your hammer / sear interface angle is positive or neutral with really rough surfaces these parts will do little to help the trigger pull. Modifications to the sear spring pressure will however produce changes in the trigger pull weight.
It work !!(25.01.2010)
I just installed the 3 springs in my 1973 BHP the job it self require some smithing ability , some roll pin in the trigger group are hard to punch out. The Hammer spring is also tricky to replace. The easiest part is the firing pin spring. My High power lost is rock hard trigger and now has a much more manageable trigger pull. while I was there I also removed the Mag release safety spring. which also help the trigger pull. Good luck
excellent(01.10.2011)
great spring set, works really well to improve trigger pull and still reliable.
BUT the hammer spring is a bit of a pain to replace (no fault of this set, just be aware) so allow some time or get some advice.
Decent kit, but there were some problems(08.04.2013)
Decided to replace the springs with lighter ones along with a trigger job on the old Hi-power. Installation was a breeze, and everything was good until I reassembled the gun and it would not function correctly. The hammer was binding. Took it all apart and found the replacement spring for the hammer was about 1/4" longer than the original and was fully compressed and binding before the hammer was fully cocked. Ended up having to cut the spring down to get it to the correct length. After that everything functions fine. The kit I ordered was part no. 206-025-001 for the pre-91 Hi-power, as my Hi-power is a 1973. Maybe I got the spring from a later Hi-power by mistake? Not too sure.
N. prodotto: 206025001 CYLINDER & SLIDE #25-A SPRING KIT Parti Fabbricante: CS025A000000002516 Kit molla di concorrenza trigger pull ridurre il peso di tirare di trigger fabbrica pesante circa 2½ libbre per un grilletto molto migliorato tirare e migliore precisione. #25A si adatta a tutte le pistole Browning Hi-Power di pre - 91, primavera del martello (1) 22 lb, (1) potenza ridotta innescare molla e molla percussore (1) potenza ridotta. #25B adatta pistole 1991 e successivamente Hi-Power e comprende (1) 22 lb martello molla e molla percussore (1) potenza ridotta.
35.9CHF10CHF 35.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
Peso della spedizione: 0.009kgLarghezza di spedizione: 83mmLunghezza di spedizione: 152mm
Dettagli dell'elemento
Made in Usa
N. prodotto: 206025002 CYLINDER & SLIDE #25-B SPRING KIT Parti Fabbricante: CS0025B000000000253 Kit molla di concorrenza trigger pull ridurre il peso di tirare di trigger fabbrica pesante circa 2½ libbre per un grilletto molto migliorato tirare e migliore precisione. #25A si adatta a tutte le pistole Browning Hi-Power di pre - 91, primavera del martello (1) 22 lb, (1) potenza ridotta innescare molla e molla percussore (1) potenza ridotta. #25B adatta pistole 1991 e successivamente Hi-Power e comprende (1) 22 lb martello molla e molla percussore (1) potenza ridotta.
29.9CHF6CHF 29.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
Reduces Pull Weight For A Light, Crisp Trigger Pull
Competition trigger pull spring kits reduce the pull weight of heavy factory triggers by approximately 2½ lbs. for a much improved trigger pull and better accuracy. #25A fits all pre-’91 Browning Hi-Power pistols, and includes (1) 22 lb. hammer spring, (1) reduced power trigger return spring, and (1) reduced power firing pin spring. #25B fits 1991 and later Hi-Power pistols, and includes (1) 22 lb. hammer spring and (1) reduced power firing pin spring.
SPECS: Spring steel. #25A includes (3) springs. #25B include (2) springs.
Altro...
Riduce il peso di tirare per un tiro di innesco leggero, croccante
Kit molla di concorrenza trigger pull ridurre il peso di tirare di trigger fabbrica pesante circa 2½ libbre per un grilletto molto migliorato tirare e migliore precisione. #25A si adatta a tutte le pistole Browning Hi-Power di pre - 91, primavera del martello (1) 22 lb, (1) potenza ridotta innescare molla e molla percussore (1) potenza ridotta. #25B adatta pistole 1991 e successivamente Hi-Power e comprende (1) 22 lb martello molla e molla percussore (1) potenza ridotta.
Punteggi dei clienti per CYLINDER & SLIDE #25-A SPRING KIT
Numero di punteggi: 4
Da brownells.com: 4
Punteggio medio: 3.3
Misleading(31.05.2012)
I installed these springs on a new BHP MK3 which originally measured 9.25 lbs at the trigger. After installation the trigger measured 9.25 lbs. The hammer spring was 4 coils longer than the stock or another manutacturer's replacement springs. This means you either have to cut the coils or pre-load the spring extensively to install it on the strut. So unless your hammer / sear interface angle is positive or neutral with really rough surfaces these parts will do little to help the trigger pull. Modifications to the sear spring pressure will however produce changes in the trigger pull weight.
It work !!(25.01.2010)
I just installed the 3 springs in my 1973 BHP the job it self require some smithing ability , some roll pin in the trigger group are hard to punch out. The Hammer spring is also tricky to replace. The easiest part is the firing pin spring. My High power lost is rock hard trigger and now has a much more manageable trigger pull. while I was there I also removed the Mag release safety spring. which also help the trigger pull. Good luck
excellent(01.10.2011)
great spring set, works really well to improve trigger pull and still reliable.
BUT the hammer spring is a bit of a pain to replace (no fault of this set, just be aware) so allow some time or get some advice.
Decent kit, but there were some problems(08.04.2013)
Decided to replace the springs with lighter ones along with a trigger job on the old Hi-power. Installation was a breeze, and everything was good until I reassembled the gun and it would not function correctly. The hammer was binding. Took it all apart and found the replacement spring for the hammer was about 1/4" longer than the original and was fully compressed and binding before the hammer was fully cocked. Ended up having to cut the spring down to get it to the correct length. After that everything functions fine. The kit I ordered was part no. 206-025-001 for the pre-91 Hi-power, as my Hi-power is a 1973. Maybe I got the spring from a later Hi-power by mistake? Not too sure.