Flexible rubber body with spring-loaded, ABS plastic covers help seal out dirt, dust and moisture to keep the lens surfaces of your EOTech holographic sight clean, scratch-free, and ready for use in all shooting conditions. Tabs on the right and left sides of the covers allow a fast, ambidextrous flip-open action with thumb or finger pressure. Front cover opens to near horizontal position to help block rain or sunlight. Rear cover folds back on top of the EOTech’s protective hood to ensure an unobstructed view through the sight. Body section installs under the EOTech protective hood, so it’s not even visible. Noise-absorbing neoprene pads dampen the sound of the rear lens cover contacting the hood during covert operations.
SPECS: Rubber body, ABS plastic covers, neoprene pads, matte black. 1 oz. (28.4g) weight. Includes Torx wrenches for installation. XPS2/3 - 23⁄8" long, 2¼" (5.7cm) wide, 1½" (3.8cm) high. 1 oz. (28.4g) weight. Fits EOTech models XPS2 and XPS3 only.
Altro...
Corpo in gomma flessibile con plastica ABS a molla, copre aiuto guarnizione fuori lo sporco, polvere e umidità per mantenere le superfici lente di vista olografico EOTech pulito, privo di graffi e pronto per l'uso in tutte le condizioni di ripresa. Schede sui lati destro e sinistro delle coperture permettono un'azione di vibrazione-aperto veloce, ambidestra con pressione del pollice o il dito. Sportello frontale si apre per vicino a posizione orizzontale a guida blocco pioggia o sole. Pieghe di copertura posteriore indietro sopra il cappuccio protettivo di EOTech per garantire una visuale attraverso il mirino. Sezione del corpo viene installato sotto il cappuccio protettivo di EOTech, quindi non è ancora visibile. Cuscinetti in neoprene per rumore-assorbente smorzano il suono del copriobiettivo posteriore contattando la cappa durante operazioni segrete.
Le specifiche tecniche: corpo in gomma, coperture in plastica ABS, cuscinetti in neoprene, opaco nero. 1 oncia (28,4 g) peso. Include chiavi Torx per installazione. XPS2/3 - 23 ⁄ 8" lungo, 2¼" (5.7 cm) di larghezza, 1½"(3.8 cm) di altezza. peso di 1 oncia (28,4 g). Adatto ai modelli EOTech XPS2 e XPS3 solo.
Altro...
Punteggi dei clienti per GG&G XPS2 & XPS3 LENS COVERS
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 3
Poor Fit(04.12.2012)
Ordered this with my new Eotech. It did not fit through you could see it was designed for the sight. Instead of sending it back, I cut four slits with a fingernail clipper (one fore and aft on each side) in in bottom of the thing and ripped this initial cut up about 2/3 the depth of the side rubber. This gave the unit the flex to fit, although I have to use a rubber band around it to hold the front flap down. Poor fit to say the least. Wish there was an alternative.
For "XPS" NOT "EXPS"(02.04.2013)
Do not order this model if you have the EXPS model Eotech, it will not fit and is made strictly for the XPS models. I ordered one and found this out the hard way but Brownells gladly accepted it as a return and GG&G squared me away on which model I needed (EXPS Scope & Lense Cover Combo #GGG-1424)I gave this 5 stars because of its quality and the GG&G and Brownells customer service.
N. prodotto: 336000038 GG&G XPS2 & XPS3 LENS COVERS Parti Fabbricante: GGG1272813157001888 Corpo in gomma flessibile con plastica ABS a molla, copre aiuto guarnizione fuori lo sporco, polvere e umidità per mantenere le superfici lente di vista olografico EOTech pulito, privo di graffi e pronto per l'uso in tutte le condizioni di ripresa. Schede sui lati destro e sinistro delle coperture permettono un'azione di vibrazione-aperto veloce, ambidestra con pressione del pollice o il dito. Sportello frontale si apre per vicino a posizione orizzontale a guida blocco pioggia o sole. Pieghe di copertura posteriore indietro sopra il cappuccio protettivo di EOTech per garantire una visuale attraverso il mirino. Sezione del corpo viene installato sotto il cappuccio protettivo di EOTech, quindi non è ancora visibile. Cuscinetti in neoprene per rumore-assorbente smorzano il suono del copriobiettivo posteriore contattando la cappa durante operazioni segrete.
69.9CHF10CHF 69.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
Flexible rubber body with spring-loaded, ABS plastic covers help seal out dirt, dust and moisture to keep the lens surfaces of your EOTech holographic sight clean, scratch-free, and ready for use in all shooting conditions. Tabs on the right and left sides of the covers allow a fast, ambidextrous flip-open action with thumb or finger pressure. Front cover opens to near horizontal position to help block rain or sunlight. Rear cover folds back on top of the EOTech’s protective hood to ensure an unobstructed view through the sight. Body section installs under the EOTech protective hood, so it’s not even visible. Noise-absorbing neoprene pads dampen the sound of the rear lens cover contacting the hood during covert operations.
SPECS: Rubber body, ABS plastic covers, neoprene pads, matte black. 1 oz. (28.4g) weight. Includes Torx wrenches for installation. XPS2/3 - 23⁄8" long, 2¼" (5.7cm) wide, 1½" (3.8cm) high. 1 oz. (28.4g) weight. Fits EOTech models XPS2 and XPS3 only.
Altro...
Corpo in gomma flessibile con plastica ABS a molla, copre aiuto guarnizione fuori lo sporco, polvere e umidità per mantenere le superfici lente di vista olografico EOTech pulito, privo di graffi e pronto per l'uso in tutte le condizioni di ripresa. Schede sui lati destro e sinistro delle coperture permettono un'azione di vibrazione-aperto veloce, ambidestra con pressione del pollice o il dito. Sportello frontale si apre per vicino a posizione orizzontale a guida blocco pioggia o sole. Pieghe di copertura posteriore indietro sopra il cappuccio protettivo di EOTech per garantire una visuale attraverso il mirino. Sezione del corpo viene installato sotto il cappuccio protettivo di EOTech, quindi non è ancora visibile. Cuscinetti in neoprene per rumore-assorbente smorzano il suono del copriobiettivo posteriore contattando la cappa durante operazioni segrete.
Le specifiche tecniche: corpo in gomma, coperture in plastica ABS, cuscinetti in neoprene, opaco nero. 1 oncia (28,4 g) peso. Include chiavi Torx per installazione. XPS2/3 - 23 ⁄ 8" lungo, 2¼" (5.7 cm) di larghezza, 1½"(3.8 cm) di altezza. peso di 1 oncia (28,4 g). Adatto ai modelli EOTech XPS2 e XPS3 solo.
Altro...
Punteggi dei clienti per GG&G XPS2 & XPS3 LENS COVERS
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 3
Poor Fit(04.12.2012)
Ordered this with my new Eotech. It did not fit through you could see it was designed for the sight. Instead of sending it back, I cut four slits with a fingernail clipper (one fore and aft on each side) in in bottom of the thing and ripped this initial cut up about 2/3 the depth of the side rubber. This gave the unit the flex to fit, although I have to use a rubber band around it to hold the front flap down. Poor fit to say the least. Wish there was an alternative.
For "XPS" NOT "EXPS"(02.04.2013)
Do not order this model if you have the EXPS model Eotech, it will not fit and is made strictly for the XPS models. I ordered one and found this out the hard way but Brownells gladly accepted it as a return and GG&G squared me away on which model I needed (EXPS Scope & Lense Cover Combo #GGG-1424)I gave this 5 stars because of its quality and the GG&G and Brownells customer service.