Rock-Solid Mounts With Patented Quick-Detach System
Quick-release lever-lock system clamps solidly to flattop rail and will not work loose even under heavy recoil—the more force acting on the lever, the tighter it locks. Depress the release tab to swing the lever open, and the mount easily lifts off the rifle. Adjustable with a flat head screwdriver or even a coin for an ultra-secure, no-slip fit on almost any Picatinny or Weaver-style rail, including over- or under-sized commercial rails. Lever may be configured to lock to the front or the rear to suit the operator’s preference. Large locking bar on the side of the mount engages the maximum amount of rail area, while the crossbolt and two integral locking lugs ensure rock-solid engagement of rail slots to prevent movement under recoil. Five heavy duty steel hex head screws (three on top, two on bottom) clamp the vertically split ring halves together. Cutouts in the ring sides and in the base reduce weight without sacrificing strength. AD-68 Aimpoint Mount is designed for Aimpoint optics or similar aiming devices requiring a single, 30mm ring, including the Comp C3 and M2/ML2/M3/ML3 series. Available in four configurations to suit a variety of mounting needs. Standard co-witnesses “iron” sights near the center of the optic when mounted on an AR-15/M16/M4 with standard-height mil-spec sights.
SPECS: 6061 T6 aluminum, hardcoat anodized, matte black. Height measured from top of rail to bottom of scope body. Standard - .940” high.
Mehr...
Rock-Solid-Halterungen mit patentiertem Schnelllösesystem
Das Schnellverschluss-Hebelsystem klemmt fest an der Dachschiene und löst sich auch bei starkem Rückstoss nicht - je mehr Kraft auf den Hebel einwirkt, desto fester rastet er ein. Drücken Sie die Freigabelasche, um den Hebel zu öffnen, und die Halterung hebt sich leicht vom Gewehr ab. Mit einem Schlitzschraubendreher oder sogar einer Münze einstellbar, um eine extrem sichere, rutschfeste Passform für fast alle Picatinny- oder Weaver-Schienen zu gewährleisten, einschliesslich über- oder untergrosser Handelsschienen. Der Hebel kann so konfiguriert werden, dass er nach vorne oder hinten einrastet, je nach Wunsch des Bedieners. Die grosse Verriegelungsstange an der Seite der Halterung nimmt die maximale Schienenfläche ein, während der Querbolzen und die zwei integrierten Verriegelungsnasen einen stabilen Eingriff der Schienenschlitze gewährleisten, um eine Bewegung beim Rückstoss zu verhindern. Fünf Sechskantschrauben aus Hochleistungsstahl (drei oben, zwei unten) klemmen die vertikal geteilten Ringhälften zusammen. Ausschnitte an den Ringseiten und im Boden reduzieren das Gewicht ohne Einbussen bei der Festigkeit. Die AD-68 Aimpoint-Halterung ist für Aimpoint-Optiken oder ähnliche Zielgeräte konzipiert, die einen einzelnen 30-mm-Ring erfordern, einschliesslich der Comp C3- und M2 / ML2 / M3 / ML3-Serien. Erhältlich in vier Konfigurationen für eine Vielzahl von Montageanforderungen. Bei der Montage an einem AR-15 / M16 / M4 mit Mil-Spec-Visieren in Standardhöhe „eiserne“ Visiere nahe der Mitte der Optik.
TECHNISCHE DATEN: 6061 T6 Aluminium, hart eloxiert, mattschwarz. Höhe gemessen von der Oberseite der Schiene bis zur Unterseite des Zielfernrohrkörpers. Standard - 0,940 Zoll hoch.
Mehr...
Kundenbewertungen zu AMERICAN DEFENSE MANUFACTURING AIMPOINT STANDARD MOUNT
Anzahl der Bewertungen: 3
Von brownells.com: 3
Durchschnittliche Bewertung: 5
Great mount, looks/works great!(01.01.2011)
I ended up getting this for my Comp C3 and it is great. Easy and quick to take on and off. Definitely worth the money.
Sturdy mount. Accurate description.(04.02.2012)
After debating between the Larue-68 and the AD-68 mount, I decided on the AD-68. It is easy to install with an Aimpoint Comp ML2. A friend uses this mount with his Vortex StrikeFire, as well. I was a little concerned about the height of the mount, due to the fact that there are three different 'height specific' models listed. As described, this one provides a center co-witness on a M4 with standard height sights. The AD-68 does not have all of the features of the Larue-68 (storage for a battery). However, it is very sturdy and well made.
Would buy again(22.07.2012)
Was time to upgrade my patrol rifle Sig M400 with red dot and folding rear sight. The red dot is an aimpoint there are a lot of mount out there but this one is easy to install and will not move. I like the standard you can still see your open sights in the lower 1/2 of the aimpoint
Artikel-Nr.: 100003650 AMERICAN DEFENSE MANUFACTURING AIMPOINT STANDARD MOUNT Herstellerproduktnummer: AD68STD818503010101 Das Schnellverschluss-Hebelsystem klemmt fest an der Dachschiene und löst sich auch bei starkem Rückstoss nicht - je mehr Kraft auf den Hebel einwirkt, desto fester rastet er ein. Drücken Sie die Freigabelasche, um den Hebel zu öffnen, und die Halterung hebt sich leicht vom Gewehr ab. Mit einem Schlitzschraubendreher oder sogar einer Münze einstellbar, um eine extrem sichere, rutschfeste Passform für fast alle Picatinny- oder Weaver-Schienen zu gewährleisten, einschliesslich über- oder untergrosser Handelsschienen. Der Hebel kann so konfiguriert werden, dass er nach vorne oder hinten einrastet, je nach Wunsch des Bedieners. Die grosse Verriegelungsstange an der Seite der Halterung nimmt die maximale Schienenfläche ein, während der Querbolzen und die zwei integrierten Verriegelungsnasen einen stabilen Eingriff der Schienenschlitze gewährleisten, um eine Bewegung beim Rückstoss zu verhindern. Fünf Sechskantschrauben aus Hochleistungsstahl (drei oben, zwei unten) klemmen die vertikal geteilten Ringhälften zusammen. Ausschnitte an den Ringseiten und im Boden reduzieren das Gewicht ohne Einbussen bei der Festigkeit. Die AD-68 Aimpoint-Halterung ist für Aimpoint-Optiken oder ähnliche Zielgeräte konzipiert, die einen einzelnen 30-mm-Ring erfordern, einschliesslich der Comp C3- und M2 / ML2 / M3 / ML3-Serien. Erhältlich in vier Konfigurationen für eine Vielzahl von Montageanforderungen. Bei der Montage an einem AR-15 / M16 / M4 mit Mil-Spec-Visieren in Standardhöhe „eiserne“ Visiere nahe der Mitte der Optik.
Art:
Standard
Basenanzahl:
1-Piece
Farbe:
Matte Black
Finish:
Black
Grösse:
Standard
Hersteller/Modell:
AR-15
Höhe:
.940''
Rohrdurchmesser des Zielfernrohres:
30mm
Versandgewicht: 0.159kgVersandhöhe: 61mmVersandbreite: 86mmVersandlänge: 145mm
Rock-Solid Mounts With Patented Quick-Detach System
Quick-release lever-lock system clamps solidly to flattop rail and will not work loose even under heavy recoil—the more force acting on the lever, the tighter it locks. Depress the release tab to swing the lever open, and the mount easily lifts off the rifle. Adjustable with a flat head screwdriver or even a coin for an ultra-secure, no-slip fit on almost any Picatinny or Weaver-style rail, including over- or under-sized commercial rails. Lever may be configured to lock to the front or the rear to suit the operator’s preference. Large locking bar on the side of the mount engages the maximum amount of rail area, while the crossbolt and two integral locking lugs ensure rock-solid engagement of rail slots to prevent movement under recoil. Five heavy duty steel hex head screws (three on top, two on bottom) clamp the vertically split ring halves together. Cutouts in the ring sides and in the base reduce weight without sacrificing strength. AD-68 Aimpoint Mount is designed for Aimpoint optics or similar aiming devices requiring a single, 30mm ring, including the Comp C3 and M2/ML2/M3/ML3 series. Available in four configurations to suit a variety of mounting needs. Standard co-witnesses “iron” sights near the center of the optic when mounted on an AR-15/M16/M4 with standard-height mil-spec sights.
SPECS: 6061 T6 aluminum, hardcoat anodized, matte black. Height measured from top of rail to bottom of scope body. Standard - .940” high.
Mehr...
Rock-Solid-Halterungen mit patentiertem Schnelllösesystem
Das Schnellverschluss-Hebelsystem klemmt fest an der Dachschiene und löst sich auch bei starkem Rückstoss nicht - je mehr Kraft auf den Hebel einwirkt, desto fester rastet er ein. Drücken Sie die Freigabelasche, um den Hebel zu öffnen, und die Halterung hebt sich leicht vom Gewehr ab. Mit einem Schlitzschraubendreher oder sogar einer Münze einstellbar, um eine extrem sichere, rutschfeste Passform für fast alle Picatinny- oder Weaver-Schienen zu gewährleisten, einschliesslich über- oder untergrosser Handelsschienen. Der Hebel kann so konfiguriert werden, dass er nach vorne oder hinten einrastet, je nach Wunsch des Bedieners. Die grosse Verriegelungsstange an der Seite der Halterung nimmt die maximale Schienenfläche ein, während der Querbolzen und die zwei integrierten Verriegelungsnasen einen stabilen Eingriff der Schienenschlitze gewährleisten, um eine Bewegung beim Rückstoss zu verhindern. Fünf Sechskantschrauben aus Hochleistungsstahl (drei oben, zwei unten) klemmen die vertikal geteilten Ringhälften zusammen. Ausschnitte an den Ringseiten und im Boden reduzieren das Gewicht ohne Einbussen bei der Festigkeit. Die AD-68 Aimpoint-Halterung ist für Aimpoint-Optiken oder ähnliche Zielgeräte konzipiert, die einen einzelnen 30-mm-Ring erfordern, einschliesslich der Comp C3- und M2 / ML2 / M3 / ML3-Serien. Erhältlich in vier Konfigurationen für eine Vielzahl von Montageanforderungen. Bei der Montage an einem AR-15 / M16 / M4 mit Mil-Spec-Visieren in Standardhöhe „eiserne“ Visiere nahe der Mitte der Optik.
TECHNISCHE DATEN: 6061 T6 Aluminium, hart eloxiert, mattschwarz. Höhe gemessen von der Oberseite der Schiene bis zur Unterseite des Zielfernrohrkörpers. Standard - 0,940 Zoll hoch.
Mehr...
Kundenbewertungen zu AMERICAN DEFENSE MANUFACTURING AIMPOINT STANDARD MOUNT
Anzahl der Bewertungen: 3
Von brownells.com: 3
Durchschnittliche Bewertung: 5
Great mount, looks/works great!(01.01.2011)
I ended up getting this for my Comp C3 and it is great. Easy and quick to take on and off. Definitely worth the money.
Sturdy mount. Accurate description.(04.02.2012)
After debating between the Larue-68 and the AD-68 mount, I decided on the AD-68. It is easy to install with an Aimpoint Comp ML2. A friend uses this mount with his Vortex StrikeFire, as well. I was a little concerned about the height of the mount, due to the fact that there are three different 'height specific' models listed. As described, this one provides a center co-witness on a M4 with standard height sights. The AD-68 does not have all of the features of the Larue-68 (storage for a battery). However, it is very sturdy and well made.
Would buy again(22.07.2012)
Was time to upgrade my patrol rifle Sig M400 with red dot and folding rear sight. The red dot is an aimpoint there are a lot of mount out there but this one is easy to install and will not move. I like the standard you can still see your open sights in the lower 1/2 of the aimpoint