Spring Pressure Keeps Front Or Rear Ramps/Bases In Place- Perfect On .45 Sights Too; Versatile, Totally Adjustable Design; Excellent Torch Clearance
Cures the "ramp slips just as the solder melts" problem with a pointed, spring-loaded plunger that keeps constant pressure on the ramp or a .45 sight, even when the solder flows. Adjusts for height, angle and amount of spring pressure. Non-marring, "V" block base centers barrel under the plunger. Holds rear sight bases in place, too. Great torch clearance.
SPECS: 2" (5.1cm) long aluminum Base. 4" (10.2cm) high overall. 1-3/8" (3.5cm) long over-arm. 2" (5.1cm) long Plunger Support, 3" (7.6cm) long Plunger Assembly.
Altro...
Pressione della molla mantiene anteriori o posteriori rampe/basi nel posto perfetto su,45 attrazioni troppo; Design versatile, completamente regolabile; Ottima torcia Clearance
Cure il problema "rampa scivola come la saldatura si scioglie" con un pistone a molla, appuntito che mantiene una pressione costante sulla rampa o una vista,45, anche quando si scorre la saldatura. Regola altezza, angolazione e la quantità di pressione della molla. Non guastare, blocco di "V" base centri barile sotto lo stantuffo. Stive posteriore vista basi in luogo, troppo. Liquidazione grande torcia.
Specifiche: 2"(5.1 cm) lunga alluminio Base. 4" (10.2 cm) alta complessiva. 1-3/8"(3,5 cm) lungo over-braccio. 2" (5.1 cm) di lunghezza supporto pistone, 3"(7,6 cm) lungo stantuffo Assembly.
Altro...
Punteggi dei clienti per BROWNELLS RAMP SOLDERING JIG
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 3.5
Love this Jig(21.05.2011)
Used this jig to silver solder Moison nagant front sights back on. Got it on perfect.
Defective(31.07.2015)
I purchased one of these jigs several years ago but did not try it out until recently. The spring-loaded plunger was not perpendicular to the base, so it sat at a slight angle of 5-10 degrees. This prevented full downward pressure onto the workpiece and tended to cause slippage. The plunger has a pointed tip which provides for a less secure hold than a flat tip. I suppose a small flat could be ground on it. To prevent sight rotation during soldering, the base needs to be sitting on a flat surface. Since temperatures are around 1000 degrees, a metal table is the only suitable work surface. The barrel needs to be level and secure as well, so a padded vise is advisable. This requires aligning the vise and metal table so the sight and barrel are level with the jig. It's a clever design, so I am returning the jig for replacement. Hopefully the next one will be more square.
N. prodotto: 080739000 BROWNELLS RAMP SOLDERING JIG050806104372 Cure il problema "rampa scivola come la saldatura si scioglie" con un pistone a molla, appuntito che mantiene una pressione costante sulla rampa o una vista,45, anche quando si scorre la saldatura. Regola altezza, angolazione e la quantità di pressione della molla. Non guastare, blocco di "V" base centri barile sotto lo stantuffo. Stive posteriore vista basi in luogo, troppo. Liquidazione grande torcia.
134.9CHF0CHF 134.90
*
In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.
Spring Pressure Keeps Front Or Rear Ramps/Bases In Place- Perfect On .45 Sights Too; Versatile, Totally Adjustable Design; Excellent Torch Clearance
Cures the "ramp slips just as the solder melts" problem with a pointed, spring-loaded plunger that keeps constant pressure on the ramp or a .45 sight, even when the solder flows. Adjusts for height, angle and amount of spring pressure. Non-marring, "V" block base centers barrel under the plunger. Holds rear sight bases in place, too. Great torch clearance.
SPECS: 2" (5.1cm) long aluminum Base. 4" (10.2cm) high overall. 1-3/8" (3.5cm) long over-arm. 2" (5.1cm) long Plunger Support, 3" (7.6cm) long Plunger Assembly.
Altro...
Pressione della molla mantiene anteriori o posteriori rampe/basi nel posto perfetto su,45 attrazioni troppo; Design versatile, completamente regolabile; Ottima torcia Clearance
Cure il problema "rampa scivola come la saldatura si scioglie" con un pistone a molla, appuntito che mantiene una pressione costante sulla rampa o una vista,45, anche quando si scorre la saldatura. Regola altezza, angolazione e la quantità di pressione della molla. Non guastare, blocco di "V" base centri barile sotto lo stantuffo. Stive posteriore vista basi in luogo, troppo. Liquidazione grande torcia.
Specifiche: 2"(5.1 cm) lunga alluminio Base. 4" (10.2 cm) alta complessiva. 1-3/8"(3,5 cm) lungo over-braccio. 2" (5.1 cm) di lunghezza supporto pistone, 3"(7,6 cm) lungo stantuffo Assembly.
Altro...
Punteggi dei clienti per BROWNELLS RAMP SOLDERING JIG
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 3.5
Love this Jig(21.05.2011)
Used this jig to silver solder Moison nagant front sights back on. Got it on perfect.
Defective(31.07.2015)
I purchased one of these jigs several years ago but did not try it out until recently. The spring-loaded plunger was not perpendicular to the base, so it sat at a slight angle of 5-10 degrees. This prevented full downward pressure onto the workpiece and tended to cause slippage. The plunger has a pointed tip which provides for a less secure hold than a flat tip. I suppose a small flat could be ground on it. To prevent sight rotation during soldering, the base needs to be sitting on a flat surface. Since temperatures are around 1000 degrees, a metal table is the only suitable work surface. The barrel needs to be level and secure as well, so a padded vise is advisable. This requires aligning the vise and metal table so the sight and barrel are level with the jig. It's a clever design, so I am returning the jig for replacement. Hopefully the next one will be more square.