Distinctive Design Adds That Individual Touch; Driver Included
Offers positive driver purchase plus a touch distinction to set your 1911 Autos apart from the others. Three, deep recesses arranged in a great-looking symmetrical design.
SPECS: Stainless steel, heat treated, .150"-50 x .250". Sold 4 screws per pak. Includes Tri-wing driver.
Altro...
Design distintivo che aggiunge tocco individuale; Driver incluso
Offre acquisto conducente positivo oltre una distinzione di tocco per impostare il tuo Autos 1911 rispetto agli altri. Tre, profondi recessi disposti in un disegno simmetrico accattivanti.
Specifiche: acciaio inossidabile, calore trattati,.150"-50 x. 250". Venduto 4 viti per Pak. Include Tri-ala driver.
Altro...
Punteggi dei clienti per BROWNELLS 1911 TRI-WING GRIP SCREWS
Numero di punteggi: 6
Da brownells.com: 6
Punteggio medio: 2.7
Don't Bother(24.06.2010)
This product, while looking good, is horrible. The driver bit, no matter how much attention is payed and cautiousness used will strip the head.
VERY TALL Heads; perfect for THICK Grip(21.07.2010)
'Should be known that these WILL Stick out CONSIDERABLY, and if you want to use them for standard thickness grips you will likely be disappointed. For THICK grips they'd be superb.! They look great in profile in any case.
Tri=wing grip screws 1911(23.12.2011)
Look great work like junk. first two of the screws have a different finish. noticed after installing, came close to striping one screw that had to be removed to match finish of other. Would not buy these again
to soft(28.07.2014)
The screw head stripsout very easily. They look good on 2 of my comp 1911's, but poor quality...
Secure(19.05.2015)
Used to replace factory screws on 7 - 1911's in the past 4 years. Remain tight. Have experienced no problems.
Alot better than the reviews (24.02.2018)
First things first, is it easy to strip a screw in general flat head or other wise? Answer: yes if you over tighten or if you have a poor fit from the driver and the fastener.
With that said I love this grip screw!!!
With the rubber o-ring installed and tightened down these things are amazing they look great and if you decide to use magpul FDE grips I cannot imagine one looking better.
I was a little worried after reading the reviews. However, I feel that they are not taking into account of what caused them to strip(that being more of a user error than a performance issue). They threaded on perfect, snugged up and tighten down perfectly. Being completely honest on one of the screws as I was torquing it down I started to feel the driver bit lose contact with the screw head. I stopped immediately repositioned my screwdriver and finished up.
I ordered these for my S&W but I but one in my build project with magpul FDEs and they look so good I want to order another set for it.
My advice just slow down and take your time. I am sad to see these screws go.
N. prodotto: 080863104 BROWNELLS 1911 TRI-WING GRIP SCREWS Offre acquisto conducente positivo oltre una distinzione di tocco per impostare il tuo Autos 1911 rispetto agli altri. Tre, profondi recessi disposti in un disegno simmetrico accattivanti.
16.9CHF6CHF 16.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
Distinctive Design Adds That Individual Touch; Driver Included
Offers positive driver purchase plus a touch distinction to set your 1911 Autos apart from the others. Three, deep recesses arranged in a great-looking symmetrical design.
SPECS: Stainless steel, heat treated, .150"-50 x .250". Sold 4 screws per pak. Includes Tri-wing driver.
Altro...
Design distintivo che aggiunge tocco individuale; Driver incluso
Offre acquisto conducente positivo oltre una distinzione di tocco per impostare il tuo Autos 1911 rispetto agli altri. Tre, profondi recessi disposti in un disegno simmetrico accattivanti.
Specifiche: acciaio inossidabile, calore trattati,.150"-50 x. 250". Venduto 4 viti per Pak. Include Tri-ala driver.
Altro...
Punteggi dei clienti per BROWNELLS 1911 TRI-WING GRIP SCREWS
Numero di punteggi: 6
Da brownells.com: 6
Punteggio medio: 2.7
Don't Bother(24.06.2010)
This product, while looking good, is horrible. The driver bit, no matter how much attention is payed and cautiousness used will strip the head.
VERY TALL Heads; perfect for THICK Grip(21.07.2010)
'Should be known that these WILL Stick out CONSIDERABLY, and if you want to use them for standard thickness grips you will likely be disappointed. For THICK grips they'd be superb.! They look great in profile in any case.
Tri=wing grip screws 1911(23.12.2011)
Look great work like junk. first two of the screws have a different finish. noticed after installing, came close to striping one screw that had to be removed to match finish of other. Would not buy these again
to soft(28.07.2014)
The screw head stripsout very easily. They look good on 2 of my comp 1911's, but poor quality...
Secure(19.05.2015)
Used to replace factory screws on 7 - 1911's in the past 4 years. Remain tight. Have experienced no problems.
Alot better than the reviews (24.02.2018)
First things first, is it easy to strip a screw in general flat head or other wise? Answer: yes if you over tighten or if you have a poor fit from the driver and the fastener.
With that said I love this grip screw!!!
With the rubber o-ring installed and tightened down these things are amazing they look great and if you decide to use magpul FDE grips I cannot imagine one looking better.
I was a little worried after reading the reviews. However, I feel that they are not taking into account of what caused them to strip(that being more of a user error than a performance issue). They threaded on perfect, snugged up and tighten down perfectly. Being completely honest on one of the screws as I was torquing it down I started to feel the driver bit lose contact with the screw head. I stopped immediately repositioned my screwdriver and finished up.
I ordered these for my S&W but I but one in my build project with magpul FDEs and they look so good I want to order another set for it.
My advice just slow down and take your time. I am sad to see these screws go.