Extends Below The Receiver For Easy, Positive Operation Fits Both .22LR & .22 Mag
EDM, titanium part drops in easily to provide a big, easy-to-hit release for fast, convenient mag changes. Contoured for a comfortable fit. Light, high-tensile titanium ensures durability and performance. 10/22® is grooved for positive engagement.
SPECS: Titanium, gray, satin finish. 10/22 - Approximately ½" (12.7mm) wide, 1½" (3.8cm) tall. Fits .22 LR, .22 Mag, .22 Hornet. Does not fit Nylon Stock models.
Plus...
S'étend en dessous du récepteur pour l'opération facile, Positive s'adapte à tous les deux .22 LR &.22 Mag
EDM, partie de titane drops en facilement d'assurer une libération grande, facile-à-coup pour changement rapide et commode de mag. Profilée pour un ajustement confortable. Lumière, titane haute résistance assure la durabilité et la performance. 10/22 ® est rainuré pour engager un dialogue constructif.
Spécifications : titane, gris, satin finition. 10/22 ® - environ ½ po (12,7 mm) de large, 1½ po (3,8 cm) de haut. 77/22 ® - ½" de large, 1¾" (4,4 cm) de haut. FITS.22 LR,.22 Mag,.22 Hornet. Ne rentre pas de modèles de Stock en Nylon.
Plus...
Évaluations client de POWER CUSTOM 10/22® MAG RELEASE
Nombre d'évaluations: 7
De brownells.com: 7
Note moyenne: 4.7
works the best(29.09.2010)
Pulled two screws and the push pin out , drop in the new mag release . WOW! it was way to easy to install and way too easy to use!! just a light push on the release and the mag drops out . not in the way.looks like a AR-15 type part.I installed on a Stainless 10-22..
works the best(01.10.2010)
Installed in a flash,,Remove 2 screws and a pin, bang done,Part looks like AR-15 stuff. Used on a stainless 10/22..
If you own a 10/22, this is a huge improvement over the factory mag release. I guarantee you won't be sorry.
Works as Advertised(21.02.2012)
Have installed 3 of these on different rifles. Changning this part out is simple - regardless of who manufactured part. Fit was perfect in each rifle. Have had no issues with any of them after several thousand rounds through each rifle.
color is off, but overall works good.(27.03.2012)
It does not match the silver powder coat color of the Ruger, even though this pic shows it is silver. It was really sticky at first but after working it a bit and cleaning some burs off my trigger group it works fine now. I do like the ribs though, they let you know your finger found the right spot!
May not fit in Takedown(07.01.2014)
I tried dropping this into my 10/22 Takedown (polymer trigger housing), but the fit was very tight and it seemed to bind on something, preventing installation, YMMV. Fitting probably would've made it work, but since the Takedown already has a decent extended mag release (albeit plastic), I just put it into my older 10/22 with metal trigger housing. Dropped into that one with no issues. As others have noted, the titanium color is a darker gray, and will not match the "stainless" parts exactly. I personally think it looks nice contrasted with the "blue" (black) parts.
Bomb Proof(17.09.2018)
Big improvement over the stock flush release. Very easy to install and use. Being made of titanium it should last forever. I like the look of raw titanium. Only a few small negatives, it does require regripping to reach it, some may find the edges sharp, and a black color options might be nice.
Référence: 713000050 POWER CUSTOM 10/22® MAG RELEASE Ref Fabricant: NONE EDM, partie de titane drops en facilement d'assurer une libération grande, facile-à-coup pour changement rapide et commode de mag. Profilée pour un ajustement confortable. Lumière, titane haute résistance assure la durabilité et la performance. 10/22 ® est rainuré pour engager un dialogue constructif.
47.9CHF4CHF 47.90
*
Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.
Fabriqué au USA
US export classification: 0A501.x
Ces articles sont contrôlés par le gouvernement des États-Unis et autorisés uniquement à être exportés vers le pays de destination finale pour être utilisés par le destinataire final ou les utilisateurs finaux identifiés dans le présent document. Ils ne peuvent être ni revendus, ni cédés à tout autre pays ou toute personne autre que le destinataire final autorisé ou l'utilisateur final, soit dans leur forme originale, soit après avoir été incorporés dans d'autres produits, sans l'accord préalable du gouvernement des États-Unis ou d'une autre manière autorisée par la législation américaine, règlements.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Extends Below The Receiver For Easy, Positive Operation Fits Both .22LR & .22 Mag
EDM, titanium part drops in easily to provide a big, easy-to-hit release for fast, convenient mag changes. Contoured for a comfortable fit. Light, high-tensile titanium ensures durability and performance. 10/22® is grooved for positive engagement.
SPECS: Titanium, gray, satin finish. 10/22 - Approximately ½" (12.7mm) wide, 1½" (3.8cm) tall. Fits .22 LR, .22 Mag, .22 Hornet. Does not fit Nylon Stock models.
Plus...
S'étend en dessous du récepteur pour l'opération facile, Positive s'adapte à tous les deux .22 LR &.22 Mag
EDM, partie de titane drops en facilement d'assurer une libération grande, facile-à-coup pour changement rapide et commode de mag. Profilée pour un ajustement confortable. Lumière, titane haute résistance assure la durabilité et la performance. 10/22 ® est rainuré pour engager un dialogue constructif.
Spécifications : titane, gris, satin finition. 10/22 ® - environ ½ po (12,7 mm) de large, 1½ po (3,8 cm) de haut. 77/22 ® - ½" de large, 1¾" (4,4 cm) de haut. FITS.22 LR,.22 Mag,.22 Hornet. Ne rentre pas de modèles de Stock en Nylon.
Plus...
Évaluations client de POWER CUSTOM 10/22® MAG RELEASE
Nombre d'évaluations: 7
De brownells.com: 7
Note moyenne: 4.7
works the best(29.09.2010)
Pulled two screws and the push pin out , drop in the new mag release . WOW! it was way to easy to install and way too easy to use!! just a light push on the release and the mag drops out . not in the way.looks like a AR-15 type part.I installed on a Stainless 10-22..
works the best(01.10.2010)
Installed in a flash,,Remove 2 screws and a pin, bang done,Part looks like AR-15 stuff. Used on a stainless 10/22..
If you own a 10/22, this is a huge improvement over the factory mag release. I guarantee you won't be sorry.
Works as Advertised(21.02.2012)
Have installed 3 of these on different rifles. Changning this part out is simple - regardless of who manufactured part. Fit was perfect in each rifle. Have had no issues with any of them after several thousand rounds through each rifle.
color is off, but overall works good.(27.03.2012)
It does not match the silver powder coat color of the Ruger, even though this pic shows it is silver. It was really sticky at first but after working it a bit and cleaning some burs off my trigger group it works fine now. I do like the ribs though, they let you know your finger found the right spot!
May not fit in Takedown(07.01.2014)
I tried dropping this into my 10/22 Takedown (polymer trigger housing), but the fit was very tight and it seemed to bind on something, preventing installation, YMMV. Fitting probably would've made it work, but since the Takedown already has a decent extended mag release (albeit plastic), I just put it into my older 10/22 with metal trigger housing. Dropped into that one with no issues. As others have noted, the titanium color is a darker gray, and will not match the "stainless" parts exactly. I personally think it looks nice contrasted with the "blue" (black) parts.
Bomb Proof(17.09.2018)
Big improvement over the stock flush release. Very easy to install and use. Being made of titanium it should last forever. I like the look of raw titanium. Only a few small negatives, it does require regripping to reach it, some may find the edges sharp, and a black color options might be nice.