Multi-port brake softens felt recoil and reduces muzzle rise. A single expansion chamber and 42 total ports, 21 on each side, angled 7° forward, provide maximum recoil control. Gunsmithing required. Comes with a .220" (nominal) diameter exit hole that must be opened up to .020" larger than bullet diameter. Can be enlarged to allow bullets up to .44 caliber. Rear exterior of comp can be machined to conform to barrel.
SPECS: 4140 steel, chrome moly (CM), in the white or 416 stainless steel (SS), satin finish. 2-5⁄8" (6.6cm) long. Outside diameter; #4 - 1" (2.5cm), .865" (22mm).
Plus...
Le frein multi-port adoucit le recul et réduit l'élévation du museau. Une seule chambre d'expansion et 42 ports totaux, 21 de chaque côté, inclinées à 7 ° vers l'avant, offrent un contrôle de recul maximal. La Forge est exigée. Livré avec un trou de sortie de 220 "(nominal) de diamètre qui doit être ouvert jusqu'à .020" plus grand que le diamètre de la balle. Peut être agrandi pour permettre des balles jusqu'au calibre. 44. L'extérieur arrière de la maquette peut être usiné pour se conformer au baril.
Spécifications : 4140 acier, chrome moly (CM), dans le blanc ou 416 inox (SS), finition satin. 2-5 ⁄ 8"(6,6 cm) de long. Diamètre extérieur ; #4 - 1"(2.5 cm),. 865" (22 mm).
Nombre d'évaluations: 2
De brownells.com: 2
Note moyenne: 5
They really work!(04.05.2011)
Can be machined into a barrel contour. Really does reduce recoil and muzzle jump. My 300WSM shoots like a 243Win with it on. Take it off, and my 18-pound rifle jumps four inches off the bag. Nothing at all wrong or deficient about this product. Have four of them on various other rifles. Love them. Just ordered another...
excellent addition to any barrel(02.06.2014)
I use this brake fitted to a 6.5 Grendel bull barrel (20"). The brake can be turned to match the barrel diameter without any problems, but you must adjust cutting speed in your lathe for the necessary interrupted cuts.
I first threaded a short segment to fit the brake and used this to hold the brake in the 3-jaw chuck with the tailstock live center in the brake muzzle. The brake can then be turned to match the barrel diameter. There is plenty of metal to do this operation.
The bore was then drilled to .020 over (N-letter drill for 6.5mm, as I recall). The brake did not fit my pre-threaded barrel muzzle flush. Instead of fitting a crush washer I machined a spacer to match the brake and barrel diameter by using the holding fixture that I machined. I inserted a steel washer behind the brake and then turned the washer to the diameter of the finished brake.
To install the brake so that it can be removed yet will not loosen, I used Permatex non-hardenening sealant--the kind you use for automotive water pump gaskets--to seal the barrel threads.
This is a nice brake that is a lot less work than machining a complete one out of a piece of stock. All my work was done using a 6" Atlas lathe and standard tooling.
Référence: 860100425 SHREWD #4 MUZZLE BRAKE 22 CALIBER 5/8-24 CHROME MOLY SILVER Ref Fabricant: NONE Le frein multi-port adoucit le recul et réduit l'élévation du museau. Une seule chambre d'expansion et 42 ports totaux, 21 de chaque côté, inclinées à 7 ° vers l'avant, offrent un contrôle de recul maximal. La Forge est exigée. Livré avec un trou de sortie de 220 "(nominal) de diamètre qui doit être ouvert jusqu'à .020" plus grand que le diamètre de la balle. Peut être agrandi pour permettre des balles jusqu'au calibre. 44. L'extérieur arrière de la maquette peut être usiné pour se conformer au baril.
79.9CHF5CHF 79.90
*
Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.
Référence: 860101425 SHREWD #4 MUZZLE BRAKE 22 CALIBER 5/8-24 SS SILVER Ref Fabricant: NONE Le frein multi-port adoucit le recul et réduit l'élévation du museau. Une seule chambre d'expansion et 42 ports totaux, 21 de chaque côté, inclinées à 7 ° vers l'avant, offrent un contrôle de recul maximal. La Forge est exigée. Livré avec un trou de sortie de 220 "(nominal) de diamètre qui doit être ouvert jusqu'à .020" plus grand que le diamètre de la balle. Peut être agrandi pour permettre des balles jusqu'au calibre. 44. L'extérieur arrière de la maquette peut être usiné pour se conformer au baril.
79.9CHF9CHF 79.90
*
Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.
Multi-port brake softens felt recoil and reduces muzzle rise. A single expansion chamber and 42 total ports, 21 on each side, angled 7° forward, provide maximum recoil control. Gunsmithing required. Comes with a .220" (nominal) diameter exit hole that must be opened up to .020" larger than bullet diameter. Can be enlarged to allow bullets up to .44 caliber. Rear exterior of comp can be machined to conform to barrel.
SPECS: 4140 steel, chrome moly (CM), in the white or 416 stainless steel (SS), satin finish. 2-5⁄8" (6.6cm) long. Outside diameter; #4 - 1" (2.5cm), .865" (22mm).
Plus...
Le frein multi-port adoucit le recul et réduit l'élévation du museau. Une seule chambre d'expansion et 42 ports totaux, 21 de chaque côté, inclinées à 7 ° vers l'avant, offrent un contrôle de recul maximal. La Forge est exigée. Livré avec un trou de sortie de 220 "(nominal) de diamètre qui doit être ouvert jusqu'à .020" plus grand que le diamètre de la balle. Peut être agrandi pour permettre des balles jusqu'au calibre. 44. L'extérieur arrière de la maquette peut être usiné pour se conformer au baril.
Spécifications : 4140 acier, chrome moly (CM), dans le blanc ou 416 inox (SS), finition satin. 2-5 ⁄ 8"(6,6 cm) de long. Diamètre extérieur ; #4 - 1"(2.5 cm),. 865" (22 mm).
Nombre d'évaluations: 2
De brownells.com: 2
Note moyenne: 5
They really work!(04.05.2011)
Can be machined into a barrel contour. Really does reduce recoil and muzzle jump. My 300WSM shoots like a 243Win with it on. Take it off, and my 18-pound rifle jumps four inches off the bag. Nothing at all wrong or deficient about this product. Have four of them on various other rifles. Love them. Just ordered another...
excellent addition to any barrel(02.06.2014)
I use this brake fitted to a 6.5 Grendel bull barrel (20"). The brake can be turned to match the barrel diameter without any problems, but you must adjust cutting speed in your lathe for the necessary interrupted cuts.
I first threaded a short segment to fit the brake and used this to hold the brake in the 3-jaw chuck with the tailstock live center in the brake muzzle. The brake can then be turned to match the barrel diameter. There is plenty of metal to do this operation.
The bore was then drilled to .020 over (N-letter drill for 6.5mm, as I recall). The brake did not fit my pre-threaded barrel muzzle flush. Instead of fitting a crush washer I machined a spacer to match the brake and barrel diameter by using the holding fixture that I machined. I inserted a steel washer behind the brake and then turned the washer to the diameter of the finished brake.
To install the brake so that it can be removed yet will not loosen, I used Permatex non-hardenening sealant--the kind you use for automotive water pump gaskets--to seal the barrel threads.
This is a nice brake that is a lot less work than machining a complete one out of a piece of stock. All my work was done using a 6" Atlas lathe and standard tooling.