Drop-In Part Helps Ensure Positive, Reliable Extraction
Tiny, high-stress synthetic rubber ring slips around the extractor spring to increase extractor tension for more reliable extraction. Eliminates spring "chatter" to prevent malfunctions caused by the extractor slipping off the cartridge rim. Helps ensure positive, consistent extraction during rapid-fire sequences.
SPECS: Synthetic rubber. Sold in a pak of 5.
Altro...
Drop-in parte contribuisce a garantire estrazione positivo, affidabile
Anello in gomma sintetica molto piccolo, alto-sollecitano scivola intorno la molla estrattore per aumentare la tensione di estrattore per l'estrazione più affidabile. Elimina la molla "chiacchiere" per prevenire malfunzionamenti causati dall'estrattore slittare fuori del cerchio di cartuccia. Contribuisce a garantire estrazione positiva, costante durante le sequenze di fuoco rapido.
Specifiche: gomma sintetica. Venduti in un pak 5.
Altro...
Punteggi dei clienti per TANKS RIFLE SHOP EXTRACTOR "DONUTS", 5-PAK
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 3
Works like it should (11.03.2015)
Very simple to install while you reassembling the bolt after a cleaning, just slip the O ring over the extractor spring and reassemble as normal.
I have these in all my AR's and they extract the case every time.. What more can be said, anything that helps the rifle work when I need it to is a good thing.
Don't buy this!!!!(15.01.2017)
Mine wedged itself out of the extracter and caused the whole bolt to not only to stick to the carrier but didn't allow it to lock when loading the next haul, I shot my third round and the bolt blew back so fast it slammed another round in and fired. Sounded like one shot, my dpms upper blew up! Peeled it wide open because the 4th haul that fired by itself blew before it was seated. Blew that magazine out of the bottom and blew a chunk at the bottom right of the reciever. These orings are are joke! And it's a ticking time bomb for disaster. This is not due to Brownell but dpmsinc. Now I need a whole new upper and am luck I didn't get hurt any worse than I did.
N. prodotto: 901000002 TANKS RIFLE SHOP EXTRACTOR "DONUTS", 5-PAK Parti Fabbricante: NONE Anello in gomma sintetica molto piccolo, alto-sollecitano scivola intorno la molla estrattore per aumentare la tensione di estrattore per l'estrazione più affidabile. Elimina la molla "chiacchiere" per prevenire malfunzionamenti causati dall'estrattore slittare fuori del cerchio di cartuccia. Contribuisce a garantire estrazione positiva, costante durante le sequenze di fuoco rapido.
12.9CHF5CHF 12.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
Drop-In Part Helps Ensure Positive, Reliable Extraction
Tiny, high-stress synthetic rubber ring slips around the extractor spring to increase extractor tension for more reliable extraction. Eliminates spring "chatter" to prevent malfunctions caused by the extractor slipping off the cartridge rim. Helps ensure positive, consistent extraction during rapid-fire sequences.
SPECS: Synthetic rubber. Sold in a pak of 5.
Altro...
Drop-in parte contribuisce a garantire estrazione positivo, affidabile
Anello in gomma sintetica molto piccolo, alto-sollecitano scivola intorno la molla estrattore per aumentare la tensione di estrattore per l'estrazione più affidabile. Elimina la molla "chiacchiere" per prevenire malfunzionamenti causati dall'estrattore slittare fuori del cerchio di cartuccia. Contribuisce a garantire estrazione positiva, costante durante le sequenze di fuoco rapido.
Specifiche: gomma sintetica. Venduti in un pak 5.
Altro...
Punteggi dei clienti per TANKS RIFLE SHOP EXTRACTOR "DONUTS", 5-PAK
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 3
Works like it should (11.03.2015)
Very simple to install while you reassembling the bolt after a cleaning, just slip the O ring over the extractor spring and reassemble as normal.
I have these in all my AR's and they extract the case every time.. What more can be said, anything that helps the rifle work when I need it to is a good thing.
Don't buy this!!!!(15.01.2017)
Mine wedged itself out of the extracter and caused the whole bolt to not only to stick to the carrier but didn't allow it to lock when loading the next haul, I shot my third round and the bolt blew back so fast it slammed another round in and fired. Sounded like one shot, my dpms upper blew up! Peeled it wide open because the 4th haul that fired by itself blew before it was seated. Blew that magazine out of the bottom and blew a chunk at the bottom right of the reciever. These orings are are joke! And it's a ticking time bomb for disaster. This is not due to Brownell but dpmsinc. Now I need a whole new upper and am luck I didn't get hurt any worse than I did.