Eigenschaften
- Waffentyp: AR-15
- Versandgewicht: 0.045kg
- Versandhöhe: 1mm
- Versandbreite: 79mm
- Versandlänge: 152mm
- UPC: 813318020192
Artikeldetails
US-Exportklassifizierung: 0A501.x

Artikel-Nr.: 100004898
Herst.-Nr.: EBRV1
813318020192 Der verlängerte Auslösehebel beschleunigt den Magazinwechsel und verbessert die Fähigkeit des Schützen, Störungen, Doppelzuführungen und Fehlfunktionen schnell und sicher zu beheben. Damit kannst du den Verschluss mit dem Abzugsfinger innerhalb des Abzugsbügels fangen und lösen, anstatt mit der anderen Hand. Drücke den Hebel nach oben, um den Verschluss nach hinten zu verriegeln; drücke leicht nach unten, um ihn freizugeben. Beide Vorgänge können durchgeführt werden, ohne die Hand vom Pistolengriff zu nehmen. Der EBRv1 wird an dem vorhandenen Verschlussrelease deines Gewehrs befestigt. Kann in wenigen Minuten installiert oder entfernt werden, ohne dauerhafte Änderungen an deinem Gewehr vorzunehmen.SPECS: Aus hochwertigem Stahl, matte schwarze Oberfläche. 2¼" (5.3cm) lang. ½ oz. (14g) Gewicht.
Not impressed, rather have the BAD lever 31.01.2017
Not impressed with it. I installed it and fit was not quite right. I feel the Magpul was better and easier to install. I wanted to give it a chance and its not for me. Will get Magpul for the next one.
AR-15 Ambi Fitment 20.10.2014
Purchased this to try on several AR-15 lowers. Sig 516, Sig M400 (it uses the same lower at the 516), a Windham lower and, a Rock River Lower. It works on all of them. Drops in easily. But, use caution when you are trying to use a small punch to remove the roll pin. Put a cloth or something round the entire area or you'll get to bare metal at the speed of light! Suggest save your pin. The one that normally comes with this EBRv1 may or, may not be in the package......And, slowly does it and, it'll drop right in. Also, use caution you don't lose the pin and spring under the latch......it can fly out or fall out and, they are small......hard to find etc. It is well designed in my opinion, solid and does it's job. but, I docked it a star because for my taste.....I would like the part that goes thru the trigger housing area, to be about 1/8" longer and, it should be bent down a few degree's to keep it down slightly lower for ease of operation. I also have a nice slip over one I bought from Tactical Link on the M400, I found that I had to bend that Tac Link one slightly out away from the lower, in order to keep it from contacting the lower where it goes thru the trigger housing......Before I did that, I was having trouble with the system failing to lock back the bolt after the mag was empty. Which is a pain because you're never sure if you had a FTF or, not. The Sig's (M400/516) need a straight down handle so it doesn't hit the left side mag release. The ambi bolt release I like the best, I bought from Troy industries.......the handles slight longer and, on the Windham and RRA's lowers it doesn't touch anything. If anyone would like to know the number of that my email is below, or they are easily found at both sites......Hope this helps.......
Beim Laden dieses Inhalts ist ein Fehler aufgetreten. Bitte aktualisiere die Seite, um fortzufahren. Wenn das Problem weiterhin besteht, wende dich bitte an unseren Kundenservice.