Fully-machined hardened steel mount with three-point mounting, provides a stable, secure base for mounting large objective scopes. Easily clamps to the charger guide dovetail and receiver mount lug without modifications to rifle. Heavy, forward locking screw gives rock solid stability at the receiver ring. Sight channel allows back-up use of iron sights without removing scope.
Komplett bearbeitete Halterung aus gehärtetem Stahl mit Dreipunktbefestigung bietet eine stabile, sichere Basis für die Befestigung grosser Objektivfernrohre. Leicht an der Schwalbenschwanzführung des Ladegeräts und an der Halterung des Empfängers zu befestigen, ohne Änderungen am Gewehr vornehmen zu müssen. Schwere, vordere Feststellschraube sorgt für Stabilität am Aufnahmering. Der Visierkanal ermöglicht die Verwendung von Eisenvisieren, ohne das Zielfernrohr zu entfernen. Weaver hat eine Weaver-artige Oberschiene. Picatinny verwendet eine Picatinny-Schiene für zusätzliche Montagemöglichkeiten. 7 "Picatinny - Erweitertes, 7" langes Picatinny-Schienensystem, mit dem Sie viele Optionen für die Sichtmontage verwenden können. Tactical verfügt über eine Picatinny-Schiene, jedoch ohne offenen Sichtkanal. Kann absolut nicht unter dem engsten Spannmoment nachgeben. Alle akzeptieren Weaver-ähnliche Ringe.
TECHNISCHE DATEN: 4140 Stahl, schwarz, nitriert. Gehärtet auf Rc 60-62. 13,6 cm lang und 4,7 cm hoch. Wiegt 310 g. 7 "Picatinny - 17,7 cm lang, 4,7 cm hoch. Wiegt 435 g.
Mehr...
Kundenbewertungen zu SMITH ENTERPRISE M14 SCOPE MOUNT
Anzahl der Bewertungen: 3
Von brownells.com: 3
Durchschnittliche Bewertung: 3.3
Should have bought a Sadlak.(14.11.2010)
I've been trying to get this mount to work for over 3 yrs. Shoots 20" high with MK IV scope adjusted to full down limit (that's 45 minutes down from mechanical center). Tried different rings (Smith, Burris Signature), adding shims between rings and mount, raising front of mount with forward setscrew. Shoots groups under 1" @ 100yds when installed per instructions with Smith rings, but 20" high. Shot like a shotgun (6" groups) with other attempts to lower point of impact. Mount manufacturer said SA, NM, M1A not manufactured to tolerance. It groups under an inch! Should have bought a Sadlak.
One of the Best Mounts for M1A/M14(16.12.2010)
This is a good Mount. A little more difficult to install than a regular mount like bolt guns but this is due to the nature of the M14. Sadlak and Smith Enterprise are very much alike if not exactly. The Mounts are manufactured to G.I. receiver specs. I have installed these on many M14's in Iraq. But some Springfield's Receivers are not to G.I. specs. You can send the rifle to Smith Enterprise or another competent gunsmith who is good with these style of rifles. I would recommend this mount wholeheartedly. I've never had problems with it that could not be overcame.
Rock Solid(09.08.2012)
Great mount, not the easiest to install but well worth the time and money. Before trying to put it on - Read the instructions!
Artikel-Nr.: 851000001 SMITH ENTERPRISE M14 SCOPE MOUNT Herstellerproduktnummer: 2006 Komplett bearbeitete Halterung aus gehärtetem Stahl mit Dreipunktbefestigung bietet eine stabile, sichere Basis für die Befestigung grosser Objektivfernrohre. Leicht an der Schwalbenschwanzführung des Ladegeräts und an der Halterung des Empfängers zu befestigen, ohne Änderungen am Gewehr vornehmen zu müssen. Schwere, vordere Feststellschraube sorgt für Stabilität am Aufnahmering. Der Visierkanal ermöglicht die Verwendung von Eisenvisieren, ohne das Zielfernrohr zu entfernen. Weaver hat eine Weaver-artige Oberschiene. Picatinny verwendet eine Picatinny-Schiene für zusätzliche Montagemöglichkeiten. 7 "Picatinny - Erweitertes, 7" langes Picatinny-Schienensystem, mit dem Sie viele Optionen für die Sichtmontage verwenden können. Tactical verfügt über eine Picatinny-Schiene, jedoch ohne offenen Sichtkanal. Kann absolut nicht unter dem engsten Spannmoment nachgeben. Alle akzeptieren Weaver-ähnliche Ringe.
Fully-machined hardened steel mount with three-point mounting, provides a stable, secure base for mounting large objective scopes. Easily clamps to the charger guide dovetail and receiver mount lug without modifications to rifle. Heavy, forward locking screw gives rock solid stability at the receiver ring. Sight channel allows back-up use of iron sights without removing scope.
Komplett bearbeitete Halterung aus gehärtetem Stahl mit Dreipunktbefestigung bietet eine stabile, sichere Basis für die Befestigung grosser Objektivfernrohre. Leicht an der Schwalbenschwanzführung des Ladegeräts und an der Halterung des Empfängers zu befestigen, ohne Änderungen am Gewehr vornehmen zu müssen. Schwere, vordere Feststellschraube sorgt für Stabilität am Aufnahmering. Der Visierkanal ermöglicht die Verwendung von Eisenvisieren, ohne das Zielfernrohr zu entfernen. Weaver hat eine Weaver-artige Oberschiene. Picatinny verwendet eine Picatinny-Schiene für zusätzliche Montagemöglichkeiten. 7 "Picatinny - Erweitertes, 7" langes Picatinny-Schienensystem, mit dem Sie viele Optionen für die Sichtmontage verwenden können. Tactical verfügt über eine Picatinny-Schiene, jedoch ohne offenen Sichtkanal. Kann absolut nicht unter dem engsten Spannmoment nachgeben. Alle akzeptieren Weaver-ähnliche Ringe.
TECHNISCHE DATEN: 4140 Stahl, schwarz, nitriert. Gehärtet auf Rc 60-62. 13,6 cm lang und 4,7 cm hoch. Wiegt 310 g. 7 "Picatinny - 17,7 cm lang, 4,7 cm hoch. Wiegt 435 g.
Mehr...
Kundenbewertungen zu SMITH ENTERPRISE M14 SCOPE MOUNT
Anzahl der Bewertungen: 3
Von brownells.com: 3
Durchschnittliche Bewertung: 3.3
Should have bought a Sadlak.(14.11.2010)
I've been trying to get this mount to work for over 3 yrs. Shoots 20" high with MK IV scope adjusted to full down limit (that's 45 minutes down from mechanical center). Tried different rings (Smith, Burris Signature), adding shims between rings and mount, raising front of mount with forward setscrew. Shoots groups under 1" @ 100yds when installed per instructions with Smith rings, but 20" high. Shot like a shotgun (6" groups) with other attempts to lower point of impact. Mount manufacturer said SA, NM, M1A not manufactured to tolerance. It groups under an inch! Should have bought a Sadlak.
One of the Best Mounts for M1A/M14(16.12.2010)
This is a good Mount. A little more difficult to install than a regular mount like bolt guns but this is due to the nature of the M14. Sadlak and Smith Enterprise are very much alike if not exactly. The Mounts are manufactured to G.I. receiver specs. I have installed these on many M14's in Iraq. But some Springfield's Receivers are not to G.I. specs. You can send the rifle to Smith Enterprise or another competent gunsmith who is good with these style of rifles. I would recommend this mount wholeheartedly. I've never had problems with it that could not be overcame.
Rock Solid(09.08.2012)
Great mount, not the easiest to install but well worth the time and money. Before trying to put it on - Read the instructions!