A damaged or poorly-cut muzzle can really hurt accuracy; sharp edges on revolver cylinder chamber mouths can cause rounds to hang up going into the cylinder - a real problem when using speedloaders. Cure both problems with this cutter.
SPECS: Cutter - 3-1/4" (8.25cm) long (except .17 caliber cutter - 2-3/8" (6cm) long). 1/2" (12.7mm) or 5/8" (15.8mm) diameter.
Plus...
Une muselière endommagée ou mal coupé peut faire vraiment mal exactitude ; les arêtes vives sur Chambre cylindre revolver bouches peuvent causer des tours raccrocher entrant dans le cylindre - un réel problème lorsque vous utilisez speedloaders. Traiter les deux problèmes avec cette coupe.
SPECS : Cutter - 3-1/4"(8,25 cm) long (sauf coupe de calibre.17 - 2-3/8" (6 cm) de long). 1/2 po (12,7 mm) ou 5/8 po (15,8 mm) diamètre.
Plus...
Évaluations client de BROWNELLS 45 17 CALIBER 1/2" CHAMFER CUTTER ONLY
Nombre d'évaluations: 2
De brownells.com: 2
Note moyenne: 3
pilot hole too large(05.11.2016)
The pilot hole is too large for the .17 cal pilots. The pilot must be shimmed with wraps of .001" stock until proper fit is attained. Only then can a nice cut be made. There is apparently a miscommunication between the pilot and cutter maker. My cutters and pilots for calibers 22 and up all fit together tightly.
45°, 5/8" Chamfering Cutter (04.06.2016)
Used this with Brownells .45 BBL. Revolver Muzzle Brass Pilot (#080-944-450) to re-crown my S&W 625PC. The brass pilot measured .4405" diameter which was a good fit for my bore (.443") diameter. The Cutter's diameter (5/8") was a good match on the guns I used it on (S&W 625, 627, & 686). The last one I used it on left chatter marks/ripples. Not sure why as it cut the others smoothly. (Hope it's not getting dull already?) Purchase Brownells Facing & Chamfering Cutter Handle (#080-589-000) to use these together.
Référence: 080588453 BROWNELLS 45 17 CALIBER 1/2" CHAMFER CUTTER ONLY Une muselière endommagée ou mal coupé peut faire vraiment mal exactitude ; les arêtes vives sur Chambre cylindre revolver bouches peuvent causer des tours raccrocher entrant dans le cylindre - un réel problème lorsque vous utilisez speedloaders. Traiter les deux problèmes avec cette coupe.
84.9CHF8CHF 84.90
*
Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.
Poids du colis: 0.005kgHauteur d'expédition: 1mmLargeur d'expédition: 83mmLongueur d'expédition: 146mm
Détails de l'article
Fabriqué au USA
Référence: 080588454 BROWNELLS 45 1/2" CHAMFERING CUTTER ONLY Une muselière endommagée ou mal coupé peut faire vraiment mal exactitude ; les arêtes vives sur Chambre cylindre revolver bouches peuvent causer des tours raccrocher entrant dans le cylindre - un réel problème lorsque vous utilisez speedloaders. Traiter les deux problèmes avec cette coupe.
79.9CHF18CHF 79.90
*
Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.
Référence: 080588625 BROWNELLS 45 5/8" CHAMFERING CUTTER ONLY Une muselière endommagée ou mal coupé peut faire vraiment mal exactitude ; les arêtes vives sur Chambre cylindre revolver bouches peuvent causer des tours raccrocher entrant dans le cylindre - un réel problème lorsque vous utilisez speedloaders. Traiter les deux problèmes avec cette coupe.
79.9CHF23CHF 79.90
*
Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.
A damaged or poorly-cut muzzle can really hurt accuracy; sharp edges on revolver cylinder chamber mouths can cause rounds to hang up going into the cylinder - a real problem when using speedloaders. Cure both problems with this cutter.
SPECS: Cutter - 3-1/4" (8.25cm) long (except .17 caliber cutter - 2-3/8" (6cm) long). 1/2" (12.7mm) or 5/8" (15.8mm) diameter.
Plus...
Une muselière endommagée ou mal coupé peut faire vraiment mal exactitude ; les arêtes vives sur Chambre cylindre revolver bouches peuvent causer des tours raccrocher entrant dans le cylindre - un réel problème lorsque vous utilisez speedloaders. Traiter les deux problèmes avec cette coupe.
SPECS : Cutter - 3-1/4"(8,25 cm) long (sauf coupe de calibre.17 - 2-3/8" (6 cm) de long). 1/2 po (12,7 mm) ou 5/8 po (15,8 mm) diamètre.
Plus...
Évaluations client de BROWNELLS 45 17 CALIBER 1/2" CHAMFER CUTTER ONLY
Nombre d'évaluations: 2
De brownells.com: 2
Note moyenne: 3
pilot hole too large(05.11.2016)
The pilot hole is too large for the .17 cal pilots. The pilot must be shimmed with wraps of .001" stock until proper fit is attained. Only then can a nice cut be made. There is apparently a miscommunication between the pilot and cutter maker. My cutters and pilots for calibers 22 and up all fit together tightly.
45°, 5/8" Chamfering Cutter (04.06.2016)
Used this with Brownells .45 BBL. Revolver Muzzle Brass Pilot (#080-944-450) to re-crown my S&W 625PC. The brass pilot measured .4405" diameter which was a good fit for my bore (.443") diameter. The Cutter's diameter (5/8") was a good match on the guns I used it on (S&W 625, 627, & 686). The last one I used it on left chatter marks/ripples. Not sure why as it cut the others smoothly. (Hope it's not getting dull already?) Purchase Brownells Facing & Chamfering Cutter Handle (#080-589-000) to use these together.