A damaged or poorly-cut muzzle can really hurt accuracy; sharp edges on revolver cylinder chamber mouths can cause rounds to hang up going into the cylinder - a real problem when using speedloaders. Cure both problems with this cutter.
SPECS: Cutter - 3-1/4" (8.25cm) long (except .17 caliber cutter - 2-3/8" (6cm) long). 1/2" (12.7mm) or 5/8" (15.8mm) diameter.
Altro...
Un muso danneggiato o mal tagliata può davvero male accuratezza; bordi taglienti sulla camera di cilindro del revolver bocche possono causare colpi di riagganciare andando nel cilindro - un vero problema quando si utilizza speedloaders. Curare entrambi i problemi con questa fresa.
Punteggi dei clienti per BROWNELLS 45 17 CALIBER 1/2" CHAMFER CUTTER ONLY
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 3
pilot hole too large(05.11.2016)
The pilot hole is too large for the .17 cal pilots. The pilot must be shimmed with wraps of .001" stock until proper fit is attained. Only then can a nice cut be made. There is apparently a miscommunication between the pilot and cutter maker. My cutters and pilots for calibers 22 and up all fit together tightly.
45°, 5/8" Chamfering Cutter (04.06.2016)
Used this with Brownells .45 BBL. Revolver Muzzle Brass Pilot (#080-944-450) to re-crown my S&W 625PC. The brass pilot measured .4405" diameter which was a good fit for my bore (.443") diameter. The Cutter's diameter (5/8") was a good match on the guns I used it on (S&W 625, 627, & 686). The last one I used it on left chatter marks/ripples. Not sure why as it cut the others smoothly. (Hope it's not getting dull already?) Purchase Brownells Facing & Chamfering Cutter Handle (#080-589-000) to use these together.
N. prodotto: 080588453 BROWNELLS 45 17 CALIBER 1/2" CHAMFER CUTTER ONLY Un muso danneggiato o mal tagliata può davvero male accuratezza; bordi taglienti sulla camera di cilindro del revolver bocche possono causare colpi di riagganciare andando nel cilindro - un vero problema quando si utilizza speedloaders. Curare entrambi i problemi con questa fresa.
84.9CHF8CHF 84.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
Peso della spedizione: 0.005kgAltezza di spedizione: 1mmLarghezza di spedizione: 83mmLunghezza di spedizione: 146mm
Dettagli dell'elemento
Made in Usa
N. prodotto: 080588454 BROWNELLS 45 1/2" CHAMFERING CUTTER ONLY Un muso danneggiato o mal tagliata può davvero male accuratezza; bordi taglienti sulla camera di cilindro del revolver bocche possono causare colpi di riagganciare andando nel cilindro - un vero problema quando si utilizza speedloaders. Curare entrambi i problemi con questa fresa.
79.9CHF18CHF 79.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
N. prodotto: 080588625 BROWNELLS 45 5/8" CHAMFERING CUTTER ONLY Un muso danneggiato o mal tagliata può davvero male accuratezza; bordi taglienti sulla camera di cilindro del revolver bocche possono causare colpi di riagganciare andando nel cilindro - un vero problema quando si utilizza speedloaders. Curare entrambi i problemi con questa fresa.
79.9CHF23CHF 79.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
A damaged or poorly-cut muzzle can really hurt accuracy; sharp edges on revolver cylinder chamber mouths can cause rounds to hang up going into the cylinder - a real problem when using speedloaders. Cure both problems with this cutter.
SPECS: Cutter - 3-1/4" (8.25cm) long (except .17 caliber cutter - 2-3/8" (6cm) long). 1/2" (12.7mm) or 5/8" (15.8mm) diameter.
Altro...
Un muso danneggiato o mal tagliata può davvero male accuratezza; bordi taglienti sulla camera di cilindro del revolver bocche possono causare colpi di riagganciare andando nel cilindro - un vero problema quando si utilizza speedloaders. Curare entrambi i problemi con questa fresa.
Punteggi dei clienti per BROWNELLS 45 17 CALIBER 1/2" CHAMFER CUTTER ONLY
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 3
pilot hole too large(05.11.2016)
The pilot hole is too large for the .17 cal pilots. The pilot must be shimmed with wraps of .001" stock until proper fit is attained. Only then can a nice cut be made. There is apparently a miscommunication between the pilot and cutter maker. My cutters and pilots for calibers 22 and up all fit together tightly.
45°, 5/8" Chamfering Cutter (04.06.2016)
Used this with Brownells .45 BBL. Revolver Muzzle Brass Pilot (#080-944-450) to re-crown my S&W 625PC. The brass pilot measured .4405" diameter which was a good fit for my bore (.443") diameter. The Cutter's diameter (5/8") was a good match on the guns I used it on (S&W 625, 627, & 686). The last one I used it on left chatter marks/ripples. Not sure why as it cut the others smoothly. (Hope it's not getting dull already?) Purchase Brownells Facing & Chamfering Cutter Handle (#080-589-000) to use these together.