Tough, steel clamp captures the bolt head, and the large-handled turnscrew depresses the ejector so the ejector pin can be safely removed or installed. Set includes turnscrews to fit both Standard and Small bolt faces; also included are separate bolt head retainers. One will fit bolt bodies up to .720" diameter (standard and small bolt face) and the other will fit AR-15/M16 bolts only. Complete AR-15/M16 Bolt Ejector Tool also available separately. Tools work on bolts with plunger-style ejectors and forward-positioned locking lugs only.
SPECS: Steel, blued. Plastic handle. Includes instructions.
Altro...
Rimozione veloce di eiettori stantuffo-stile
Morsetto duro, in acciaio acquisisce la testa del bullone e la grande gestito iniziò deprime l'eiettore così il perno può essere tranquillamente rimosso o installato. Il set include turnscrews per adattarsi sia Standard sia piccole facce bullone; è inclusi anche separata bullone testa fermi. Uno si adatta bullone corpi fino a. diametro 720"(faccia del bullone standard e piccoli) e l'altro si adatta AR-15/M16 bulloni solo. Completo strumento espulsore AR-15/M16 bullone disponibili anche separatamente. Strumenti funzionano sui bulloni con eiettori stantuffo-stile e posizionato avanti bloccaggio alette solo.
Specifiche: acciaio, brunito. Manico in plastica. Include istruzioni.
Altro...
Punteggi dei clienti per BROWNELLS BOLT EJECTOR TOOL SET
Numero di punteggi: 6
Da brownells.com: 6
Punteggio medio: 2.3
not recommended(19.01.2010)
This tool is not recommended for ar bolts. It moves around too much when trying to drive roll pin out and does not secure the bolt .
Great Tool(09.04.2011)
Works exactly as advertised
Economical tool for the job(30.04.2012)
Read the instructions... My only gripe is one thing,"You have to clamp it real good while installing the roll pin.
Needs offset(20.04.2014)
Worked ok, but with AR bolt ejector, would be better if screw in device was offset to engage ejector and not in center.
fell apart(29.09.2014)
The cylinder section in the handle fell out. Seemed like it would work great but I can't tighten the driver part of the tool to depress the ejector.
A disappointment. Failed(01.03.2015)
After 38 years of trying to remove the AR ejector without assistance I finally broke down and purchased this tool. It did not hold up. The jaws bent. The handle separated. It was marginally helpful at best. I upgraded to the more expensive but much better Brownell's ejector tool that can be placed on the bench. The more expensive tool is far superior and makes ejector removal a snap.
N. prodotto: 080792100 BROWNELLS BOLT EJECTOR TOOL SET Morsetto duro, in acciaio acquisisce la testa del bullone e la grande gestito iniziò deprime l'eiettore così il perno può essere tranquillamente rimosso o installato. Il set include turnscrews per adattarsi sia Standard sia piccole facce bullone; è inclusi anche separata bullone testa fermi. Uno si adatta bullone corpi fino a. diametro 720"(faccia del bullone standard e piccoli) e l'altro si adatta AR-15/M16 bulloni solo. Completo strumento espulsore AR-15/M16 bullone disponibili anche separatamente. Strumenti funzionano sui bulloni con eiettori stantuffo-stile e posizionato avanti bloccaggio alette solo.
48.9CHF0CHF 48.90
*
In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.
Adatto per:
AR-15
Peso della spedizione: 0.181kgAltezza di spedizione: 10mmLarghezza di spedizione: 41mmLunghezza di spedizione: 132mm
Dettagli dell'elemento
Made in Usa
N. prodotto: 080792002 BROWNELLS AR-15/M16 BOLT EJECTOR TOOL Morsetto duro, in acciaio acquisisce la testa del bullone e la grande gestito iniziò deprime l'eiettore così il perno può essere tranquillamente rimosso o installato. Il set include turnscrews per adattarsi sia Standard sia piccole facce bullone; è inclusi anche separata bullone testa fermi. Uno si adatta bullone corpi fino a. diametro 720"(faccia del bullone standard e piccoli) e l'altro si adatta AR-15/M16 bulloni solo. Completo strumento espulsore AR-15/M16 bullone disponibili anche separatamente. Strumenti funzionano sui bulloni con eiettori stantuffo-stile e posizionato avanti bloccaggio alette solo.
29.9CHF0CHF 29.90
*
In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.
Tough, steel clamp captures the bolt head, and the large-handled turnscrew depresses the ejector so the ejector pin can be safely removed or installed. Set includes turnscrews to fit both Standard and Small bolt faces; also included are separate bolt head retainers. One will fit bolt bodies up to .720" diameter (standard and small bolt face) and the other will fit AR-15/M16 bolts only. Complete AR-15/M16 Bolt Ejector Tool also available separately. Tools work on bolts with plunger-style ejectors and forward-positioned locking lugs only.
SPECS: Steel, blued. Plastic handle. Includes instructions.
Altro...
Rimozione veloce di eiettori stantuffo-stile
Morsetto duro, in acciaio acquisisce la testa del bullone e la grande gestito iniziò deprime l'eiettore così il perno può essere tranquillamente rimosso o installato. Il set include turnscrews per adattarsi sia Standard sia piccole facce bullone; è inclusi anche separata bullone testa fermi. Uno si adatta bullone corpi fino a. diametro 720"(faccia del bullone standard e piccoli) e l'altro si adatta AR-15/M16 bulloni solo. Completo strumento espulsore AR-15/M16 bullone disponibili anche separatamente. Strumenti funzionano sui bulloni con eiettori stantuffo-stile e posizionato avanti bloccaggio alette solo.
Specifiche: acciaio, brunito. Manico in plastica. Include istruzioni.
Altro...
Punteggi dei clienti per BROWNELLS BOLT EJECTOR TOOL SET
Numero di punteggi: 6
Da brownells.com: 6
Punteggio medio: 2.3
not recommended(19.01.2010)
This tool is not recommended for ar bolts. It moves around too much when trying to drive roll pin out and does not secure the bolt .
Great Tool(09.04.2011)
Works exactly as advertised
Economical tool for the job(30.04.2012)
Read the instructions... My only gripe is one thing,"You have to clamp it real good while installing the roll pin.
Needs offset(20.04.2014)
Worked ok, but with AR bolt ejector, would be better if screw in device was offset to engage ejector and not in center.
fell apart(29.09.2014)
The cylinder section in the handle fell out. Seemed like it would work great but I can't tighten the driver part of the tool to depress the ejector.
A disappointment. Failed(01.03.2015)
After 38 years of trying to remove the AR ejector without assistance I finally broke down and purchased this tool. It did not hold up. The jaws bent. The handle separated. It was marginally helpful at best. I upgraded to the more expensive but much better Brownell's ejector tool that can be placed on the bench. The more expensive tool is far superior and makes ejector removal a snap.