Increased pressure stabilizes the follower and improves feeding, especially on high-capacity magazines. SIG P220 provides 10% more power in your older .45 ACP Sig P220 and is the factory standard spring in newer P220s with a green recoil spring. Also fits the Browning BDA .45 ACP. Separate models available for magazines with a metal floorplate (MF) or a plastic floorplate (PF). Will not fit 8-round magazines made by Mec-Gar.
SPECS: Will not fit Meg-Gar Sig 220 magazines and 70873 fits Metal Floor plate Sig 220 and BDA magazines only, 79383 fits Plastic Floor plate Sig 220 magazines only.
Altro...
Migliore alimentazione per il semi-automatico
Aumento della pressione si stabilizza il seguace e migliora l'alimentazione, specialmente su riviste ad alta capacità. SIG P220 fornisce potenza del 10% in più nel vostro vecchio,45 ACP Sig P220 ed è la molla standard di fabbrica in P220s più recenti con una molla di rinculo verde. Si inserisce anche il Browning BDA,45 ACP. Modelli separati per riviste con una piastra di metallo (MF) o una piastra di plastica (PF). Non si adatterà riviste 8-rotonda fatte da Mec-Gar.
Specifiche: non si adatterà Meg-Gar Sig 220 riviste e 70873 adatta piano metallo piastra 220 Sig BDA riviste e solo, 79383 si inserisce riviste di plastica piano piastra 220 Sig solo.
Altro...
Punteggi dei clienti per WOLFF +10% POWER SPRING, 3-PAK FITS SIG HI-CAP P226, P228, P229
Numero di punteggi: 3
Da brownells.com: 3
Punteggio medio: 3.7
Doesn't work correctly(08.09.2017)
Standard (factory) Sig P220 magazines have 6 coils at the top that are wound smaller to fit inside the follower when compressed, and then get bigger on the lower coils. These springs are large coils for the entire length, so when compressed they do not fit inside the follower. This means they stack up below the follower and end up being too tall, which means you can't get 8 rounds in the magazine no matter how hard you try.
My suggestion is buy the replacement springs for 10-round P220 mags (which DO) have the smaller coils on top, and trim them so they have the same number of coils are the factory 8-round springs. Thats what I ended up doing, works great.
Just what was needed!!!(16.09.2011)
I recently purchased a few Mec-Gar extended capacity mags for my Sig P226 .40 cal. Straight out of the box, I noticed the mag springs were not strong enough to lock the slide back after firing the last round. I ordered the Wolff +10% and they were exactly what was needed! I haven't had one single malfunction or the slide failing to lock back since. A great low cost solution!
Restores old Sig magazines(23.04.2015)
Bought These for an older Sig P226 9mm from 1989 that was given to me. The old springs were the factory original and they didn't have a lot of power left in them. The new springs took them back to feeling like new magazines and I could feel the difference right away while loading and firing. Nice for the slide to lock open again when I'm empty.
N. prodotto: 969000057 WOLFF +10% POWER SPRING, 3-PAK FITS SIG HI-CAP P226, P228, P229 Parti Fabbricante: 74373 Aumento della pressione si stabilizza il seguace e migliora l'alimentazione, specialmente su riviste ad alta capacità. SIG P220 fornisce potenza del 10% in più nel vostro vecchio,45 ACP Sig P220 ed è la molla standard di fabbrica in P220s più recenti con una molla di rinculo verde. Si inserisce anche il Browning BDA,45 ACP. Modelli separati per riviste con una piastra di metallo (MF) o una piastra di plastica (PF). Non si adatterà riviste 8-rotonda fatte da Mec-Gar.
36.9CHF0CHF 36.90
*
In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.
Caratteristiche:Adatto per: Sig SauerModello: Universal HandgunsQuantità: 3
Adatto per:
Sig Sauer
Modello:
Universal Handguns
Quantità: 3 Peso della spedizione: 0.027kgAltezza di spedizione: 18mmLarghezza di spedizione: 64mmLunghezza di spedizione: 277mm
Dettagli dell'elemento
Made in Usa
N. prodotto: 969000220 WOLFF +10% POWER SPRING, 3-PAK FITS SIG P220/BROWNING BDA MF Parti Fabbricante: 70873 Aumento della pressione si stabilizza il seguace e migliora l'alimentazione, specialmente su riviste ad alta capacità. SIG P220 fornisce potenza del 10% in più nel vostro vecchio,45 ACP Sig P220 ed è la molla standard di fabbrica in P220s più recenti con una molla di rinculo verde. Si inserisce anche il Browning BDA,45 ACP. Modelli separati per riviste con una piastra di metallo (MF) o una piastra di plastica (PF). Non si adatterà riviste 8-rotonda fatte da Mec-Gar.
34.9CHF5CHF 34.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
Caratteristiche:Adatto per: Sig SauerModello: P220Quantità: 3
Adatto per:
Sig Sauer
Modello:
P220
Quantità: 3 Peso della spedizione: 0.045kgAltezza di spedizione: 10mmLarghezza di spedizione: 51mmLunghezza di spedizione: 193mm
Increased pressure stabilizes the follower and improves feeding, especially on high-capacity magazines. SIG P220 provides 10% more power in your older .45 ACP Sig P220 and is the factory standard spring in newer P220s with a green recoil spring. Also fits the Browning BDA .45 ACP. Separate models available for magazines with a metal floorplate (MF) or a plastic floorplate (PF). Will not fit 8-round magazines made by Mec-Gar.
SPECS: Will not fit Meg-Gar Sig 220 magazines and 70873 fits Metal Floor plate Sig 220 and BDA magazines only, 79383 fits Plastic Floor plate Sig 220 magazines only.
Altro...
Migliore alimentazione per il semi-automatico
Aumento della pressione si stabilizza il seguace e migliora l'alimentazione, specialmente su riviste ad alta capacità. SIG P220 fornisce potenza del 10% in più nel vostro vecchio,45 ACP Sig P220 ed è la molla standard di fabbrica in P220s più recenti con una molla di rinculo verde. Si inserisce anche il Browning BDA,45 ACP. Modelli separati per riviste con una piastra di metallo (MF) o una piastra di plastica (PF). Non si adatterà riviste 8-rotonda fatte da Mec-Gar.
Specifiche: non si adatterà Meg-Gar Sig 220 riviste e 70873 adatta piano metallo piastra 220 Sig BDA riviste e solo, 79383 si inserisce riviste di plastica piano piastra 220 Sig solo.
Altro...
Punteggi dei clienti per WOLFF +10% POWER SPRING, 3-PAK FITS SIG HI-CAP P226, P228, P229
Numero di punteggi: 3
Da brownells.com: 3
Punteggio medio: 3.7
Doesn't work correctly(08.09.2017)
Standard (factory) Sig P220 magazines have 6 coils at the top that are wound smaller to fit inside the follower when compressed, and then get bigger on the lower coils. These springs are large coils for the entire length, so when compressed they do not fit inside the follower. This means they stack up below the follower and end up being too tall, which means you can't get 8 rounds in the magazine no matter how hard you try.
My suggestion is buy the replacement springs for 10-round P220 mags (which DO) have the smaller coils on top, and trim them so they have the same number of coils are the factory 8-round springs. Thats what I ended up doing, works great.
Just what was needed!!!(16.09.2011)
I recently purchased a few Mec-Gar extended capacity mags for my Sig P226 .40 cal. Straight out of the box, I noticed the mag springs were not strong enough to lock the slide back after firing the last round. I ordered the Wolff +10% and they were exactly what was needed! I haven't had one single malfunction or the slide failing to lock back since. A great low cost solution!
Restores old Sig magazines(23.04.2015)
Bought These for an older Sig P226 9mm from 1989 that was given to me. The old springs were the factory original and they didn't have a lot of power left in them. The new springs took them back to feeling like new magazines and I could feel the difference right away while loading and firing. Nice for the slide to lock open again when I'm empty.