Eigenschaften
- Art: -
- Modell: 10/22
- Waffentyp: Ruger
- Versandgewicht: 0.204kg
- Versandhöhe: 36mm
- Versandbreite: 99mm
- Versandlänge: 157mm
- UPC: 081950102211
Artikeldetails
US-Exportklassifizierung: 0A501.c

Artikel-Nr.: 883000038
Herst.-Nr.: 1022-1C
081950102211 Der Timney 10/22® Abzug wird zweifellos den Standard für zukünftige Nachrüstungen von Abzügen für den Ruger® 10-22® setzen. Mit einem einteiligen Gehäuse aus CNC-bearbeitetem 6061-T6 Flugzeug-Aluminium ist der Timney-Abzug für den Ruger® 10-22® ein vollständiger Ersatz des Abzugsmechanismus. Der Abzug, der Sear und der Hammer sind aus Draht-EDM geschnitten und aus wärmebehandeltem Stahl gefertigt, was aussergewöhnliche Haltbarkeit gewährleistet. Drücke die beiden Gehäusestifte heraus und "drop in" die komplette Abzugseinheit von Timney. Der Timney 10-22® Abzug verfügt über einen von Timney entworfenen verlängerten Magazinrelease, der mit einem Finger für aussergewöhnliche Benutzerfreundlichkeit und Zugänglichkeit bedient werden kann. Ausserdem kommt er standardmässig mit einem automatischen Bolzenfreigabesystem. Wie bei allen Timney-Abzügen, die in den USA hergestellt werden, wird jeder vollständige Ersatzmechanismus von Hand montiert, kalibriert und getestet, um eine lebenslange zuverlässige Leistung zu gewährleisten. Der Abzug ist ab Werk auf 2 Pfund eingestellt, ohne Nachlauf.Best drop in trigger group 05.03.2015
This is the best drop in trigger group I've tried. East to install. Great feel, and break. Reset is perfect. Looks great. Mag release is a nice change. Finally, the bolt catch is more user friendly.
Timney is the go to trigger group for me!
Great Hunting Trigger 27.07.2013
Built a 10/22 using:
Timney 10/22 Drop-In Trigger Assembly 883-000-038WB -- great trigger, drop in with no fitting required. The lever magazine release is a great addition, helping with making the rifle a little more ambidextrous. The spring loaded bolt release works as we are accustomed to unlike the factory release. The trigger pull is crisp and clean reminiscent of the Jewel triggers on my 700. The trigger is a vast improvement over factory. 4 stars as the pull measured 3lbs on my Lyman gauge, preferred for hunting but as it is not adjustable I don't consider this a bench rest trigger.
ER Shaw Fluted 10/22 .920 Target Barrel, SS 100-004-747WB -- everything I was looking for. Looks great and shoots great. 1/2" groups at 75 yards on a 100 degree, 10 - 15 mph gusty day with 20 year old Remington Golden Bullet HP, very satisfying. The barrel dropped right into the action and was installed using the factory V-block without barrel droop. The V-block barrel retainer screws were just snugged. Checked with a set of headspace gauges and everything was fine and good to go. A 5 star barrel for sure.
Hogue 10/22 Overmolded Rifle Stock B/B Rubber Covering 408-220-100WB -- The stock I wanted was out of stock so I got this one to do the build. I am liking it. Feels good in hand and on the shoulder. Ambidextrous Bedding was accurate and felt solid. With the action screw torqued to 18 in-lbs the Shaw barrel was dollar bill free floated from 1" behind the flutes to the muzzle. The semi-varmint fore end is a joy in hand or on a bag. 4 Stars as the fore end will flex enough to touch the barrel with moderate straight line side hand pressure, a hasty sling or tight sling. Still I may well forget about the stock I wanted that cost 2-1/2 times as much, this one shoots and feels so good.
Volquartsen 10/22 Socket Head Takedown Screw 930-000-O26WB -- Comparing this screw to my factory screw it is about 2-1/2 threads shorter. However it fit this build just fine, earning it 5 Stars. It and the receiver handled 18 in-lbs of torque without problem.
Beim Laden dieses Inhalts ist ein Fehler aufgetreten. Bitte aktualisiere die Seite, um fortzufahren. Wenn das Problem weiterhin besteht, wende dich bitte an unseren Kundenservice.