Il Carrello è vuoto.

Carrello

0917309915

Suisse / Schweiz

Lingue: Deutsch Français Italiano

TIMNEY
308 AR DROP-IN TRIGGER MODULE SOLID SHOE

081950006700 883000023

Obtain A Super-Smooth Pull & Crisp Letoff In Minutes

Self-contained module is ready to install in your small-pin AR and deliver an exceptionally smooth, crisp, creep-free single-stage trigger pull that feels more like a traditional bolt action than a combat rifle trigger. 100% drop-in—no gunsmithing, fitting, or adjusting required. All components are captive in the lightweight, aluminum alloy housing. Hammer is wire-EDM machined from S7 tool steel that combines hardness to resist wear with superior impact resistance to withstand heavy use without chipping or breaking. Other components are EDM cut from A2 tool steel, then heat treated to Rc 56-60 for long service life. Precision-ground engagement surfaces ensure superb reliability and a crisp, clean hammer release. Installs using your rifle’s original hammer/trigger pins; proprietary design eliminates pin walkout. AR-.308 model has a factory-set 4 lb. pull weight, a solid shoe, and more hammer mass to ensure positive ignition of harder .308/7.62mm primers.

SPECS: Hammer – S7 tool steel, natural color, Teflon-Nickel coated. Trigger/Internal Components - Hardened A2 tool steel, black oxide finish. Housing – 6061 T6 aluminum, gold anodized finish. Fits rifles with .154" diameter hammer/trigger pin holes. Will not fit Colt-manufactured AR-15s with sear block. AR-.308 – non-adjustable 4 lb. pull weight. Fits AR-style .308 rifles that accept small-pin AR-15 trigger components.

Altro...

Ottenere una super-liscia Pull & Letoff croccante In pochi minuti

Modulo autonomo è pronto da installare nel tuo piccolo poli AR e consegnare un tiro di innesco di singolo stadio eccezionalmente liscio, fresco, privo di creep che si sente più come un'azione bullone tradizionale di un trigger rifle combattimento. goccia-in 100% — nessun gunsmithing, montaggio, o regolazione necessaria. Tutti i componenti sono trattenuti in alluminio leggero, alloggiamento della lega. Martello è elettroerosione a filo lavorati in acciaio da utensili S7 che combina durezza per resistere all'usura con resistenza agli urti superiore per resistere all'uso pesante senza scheggiare o rompere. Altri componenti sono EDM tagliato dalla A2 acciaio da utensili, quindi il calore trattato a Rc 56-60 per la lunga vita di servizio. Superfici di precisione-terra impegno garantiscono affidabilità superba e un rilascio martello fresco, pulito. Installa utilizzando i perni di trigger/martello originale del vostro fucile; design proprietario elimina sciopero del perno. Modello AR-308 ha un peso di trazione impostato in fabbrica 4 etti, una solida scarpa e più massa del martello per assicurare ad accensione comandata dei primer di.308/7.62mm più difficile.

Specifiche: martello – S7 strumento colore naturale, acciaio, Teflon-Nichel rivestito. Finitura interna/grilletto componenti - acciaio da utensili indurito A2, ossido nero. Alloggiamento-6061 T6 alluminio, finitura anodizzato oro. Si adatta a fucili con. 154 trigger/martello perno fori di diametro ". Non si adatterà fabbricati Colt AR-15s con blocco scottare. AR-308- peso di tirare non regolabile 4 lb. Si adatta a fucili AR-stile 308 che accettano piccoli poli AR-15 componenti di innesco.

Altro...

Punteggi dei clienti per TIMNEY AR .308 TRIGGER MODULE, 4 LBS, SOLID SHOE

Numero di punteggi: 12
Da brownells.com: 12
Punteggio medio: 4.7

Nothing to Write Home About (02.07.2010)

This trigger is difficult to install. There are two tiny allen head lock screws that must be manuvered into place next to the hammer springs. Very hard to do without three hands.
Performance is only so-so after installation. No take up or slop but it seems to be set at about 8 pounds.
Better than the stock trigger to be sure but not worth the money. Timney usually does a better job on their triggers.

AR-.308 Trigger Module, Solid Shoe (19.07.2010)

Installed mine quite easily. Instructions are adequate but could be improved and Timney has techs available to assist/answer questions. There might be a small amount of creap in mine but if so, I see it as a good thing for this application.

Best thing I have added to my AR Varmint (24.05.2011)

I have built several AR's over the past several years, but always stoned the triggers and added lighter springs to get a better trigger pull. I wanted a 'drop in unit', and having had great results with other "Timmney" Triggers, went with this unit. This trigger is amazing compared to any other trigger I have used in a AR. As for the two screws that had to be installed, I spet maybe a full sixty seconds getting both in and tight. No problem!!

Make em Jealous. (15.09.2011)

I installed this trigger in my SASS build project. Took the rifle to the gon shop because of an unrelated issue. The people at the shop fell in love with the trigger just like I did. In fact one of the gunsmiths had a SASS and the first thing out of his mouth is "man, im jealous of that trigger." Its smooth and exact. Im going to install a Timney in my Remington Woodsmaster if they make one.

Wow, what a difference! (30.12.2011)

I recommend this trigger. The pull is consistent and the break is very clean. If you own a stock DPMS LR-308 with a factory trigger that takes FOREVER to break, you will not be disappointed with this purchase. I installed it myself after I watched a couple of videos as well as going to Timney's website and viewing the installation presentation. On a side note, if you are not mechanically inclined, have a friend install it who is.

GREAT TRIGGER!!! Hard to install (11.01.2012)

I have built many AR's and have done many trigger Jobs for customers and friends, but this trigger is GOLD right out of the box. IT is very difficult to install, not impossible, but not easy by ones self. making sure the trigger pins stay seated as you tighten the two allens can be frustrating but it is well worth it in the end. My trigger feels about 3 pounds at the most.... no creep, exactly what I expect from a [$] trigger.

I want to rate this trigger 10 stars! (02.06.2012)

Unquestionably the best upgrade/modification to my DPMS ar-15! Accuracy much improved from stock trigger. Easy install too. There are two retaining hex screws under the end length of the hammer spring that can be tricky. After studying the trigger & install instructions I took the ends of the hammer spring partially blocking the retainer hex screws & lifted both ends crossing them to the middle over each other. This cleared the area for installing the hex retaining screws. After both hex screws were installed, the hammer spring ends were uncrossed and fell back into their original place. The 4 lbs pull was unchanged by the prying up & crossing of the spring ends. Excellent trigger! Well worth the $$

Excellent! (15.01.2014)

Installed in a Ruger SR762 in minutes, per instructions. Would recommend watching You Tube related video. Went from factory 10.75 lb drag and creep to a crisp 4.0 lb trigger.

Great AR upgrade. (02.01.2015)

Easy install in my Bushmaster. Crisp trigger that took the long, hard, gritty pull out of my AR 10. I will buy another one for my 5.56. Can't wait to see how it performs at the range.

Phoned in. (25.03.2015)

4 lb pull is too heavy, I don't know why Timney made it so heavy. 3lb would have been perfect. They make a good trigger, but I think they have been resting on their laurels.

Nothing Not To Like (23.06.2015)

My first experience with Timney triggers was one I bought for my 10/22. Total drop in, great fit, great trigger. So I got this one for my DPMS style .308 AR build and it is everything I expected. Two triggers purchased, two great feeling triggers; do I detect a pattern?

Iâve purchased stripped AR lowers and built them up. With the last one I purchased a Ni Boron set and that was the best AR trigger Iâd tried. Iâm mentioning this to point out that I *DO* know how to install Mil Spec triggers and know what a good one feels like. Since I wanted a rifle that would be as accurate as possible I decided to actually put some money into this trigger. I could have gone with other manufacturers but while I do know how to install the fire control group I can get a bit lazy from time to time. So I looked into drop in triggers.

I wanted a trigger that was light enough to not impact my accuracy too much (Iâve got enough problems as is) but was heavy enough that I wouldnât worry about safety out in the field. Timneyâs 4 pound trigger seems to fit the bill. I followed the directions and installation was a snap. I saw one review complaining about the pins falling out. I had to laugh as the directions said to put a piece of tape over the pins until installation was complete. Once youâve tightened down the set screws to apply pressure to the pins (the last step) you can remove the tape and the pins are as tight as you could possibly want.

Iâve tried custom worked triggers on other guns at the range (not my guns but ones belonging to someone else) and while they might be a bit lighter I donât think that they break any crisper or have any less creep (i.e. none).

Any time I want an accurate trigger that is easy to install Iâm going to go with Timney for sure.

Crisp - Zero Creep in a DPMS GII Lower (11.01.2016)

No more creep. Light, repeatable release and feels like winding a Swiss watch while depressing the trigger. Trigger total movement is about 1/8"!

Instructions were spot on. Read them through first. One change would be to start the set screws before you drop it in. Just a turn. Too much and the pins won't go back in. After you have the assembly in position it's a bit of a chore to get them started because of the springs. Use grease in the socket to hold the screws to the wrench.

I put this in a new DPMS Gen II lower. Fits like a glove. The GII lower is different than the GI (LR-308) but rest assured it fits perfectly.

The hammer is bigger than the GII OEM hammer. The whole thing is a piece of art. High quality metal and finish.

Worth the money.

Leggi più recensioni su brownells.com

449.9 449.9 1 CHF

N. prodotto: 883000023
TIMNEY AR .308 TRIGGER MODULE, 4 LBS, SOLID SHOE
Parti Fabbricante: 670 081950006700 Modulo autonomo è pronto da installare nel tuo piccolo poli AR e consegnare un tiro di innesco di singolo stadio eccezionalmente liscio, fresco, privo di creep che si sente più come un'azione bullone tradizionale di un trigger rifle combattimento. goccia-in 100% — nessun gunsmithing, montaggio, o regolazione necessaria. Tutti i componenti sono trattenuti in alluminio leggero, alloggiamento della lega. Martello è elettroerosione a filo lavorati in acciaio da utensili S7 che combina durezza per resistere all'usura con resistenza agli urti superiore per resistere all'uso pesante senza scheggiare o rompere. Altri componenti sono EDM tagliato dalla A2 acciaio da utensili, quindi il calore trattato a Rc 56-60 per la lunga vita di servizio. Superfici di precisione-terra impegno garantiscono affidabilità superba e un rilascio martello fresco, pulito. Installa utilizzando i perni di trigger/martello originale del vostro fucile; design proprietario elimina sciopero del perno. Modello AR-308 ha un peso di trazione impostato in fabbrica 4 etti, una solida scarpa e più massa del martello per assicurare ad accensione comandata dei primer di.308/7.62mm più difficile.

449.9 CHF 7 CHF 449.90 *

Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.

Caratteristiche: Adatto per: AR .308 Tipo: Non regolabile

Aggiungi alla lista degli acquisti

Domande

Dettagli

Aggiungi alla lista degli acquisti

Domande

Caratteristiche

Adatto per: AR .308 Tipo: Non regolabile Peso della spedizione: 0.068kg Altezza di spedizione: 33mm Larghezza di spedizione: 91mm Lunghezza di spedizione: 191mm

Dettagli dell'elemento

Made in Usa
Classificazione per l'export dagli US: 0A501.c

Obtain A Super-Smooth Pull & Crisp Letoff In Minutes

Altro...

Ottenere una super-liscia Pull & Letoff croccante In pochi minuti

Altro...

Punteggi dei clienti per TIMNEY AR .308 TRIGGER MODULE, 4 LBS, SOLID SHOE

Numero di punteggi: 12
Da brownells.com: 12
Punteggio medio: 4.7

Nothing to Write Home About (02.07.2010)

AR-.308 Trigger Module, Solid Shoe (19.07.2010)

Best thing I have added to my AR Varmint (24.05.2011)

Make em Jealous. (15.09.2011)

Wow, what a difference! (30.12.2011)

GREAT TRIGGER!!! Hard to install (11.01.2012)

I want to rate this trigger 10 stars! (02.06.2012)

Excellent! (15.01.2014)

Installed in a Ruger SR762 in minutes, per instructions. Would recommend watching You Tube related video. Went from factory 10.75 lb drag and creep to a crisp 4.0 lb trigger.

Great AR upgrade. (02.01.2015)

Easy install in my Bushmaster. Crisp trigger that took the long, hard, gritty pull out of my AR 10. I will buy another one for my 5.56. Can't wait to see how it performs at the range.

Phoned in. (25.03.2015)

4 lb pull is too heavy, I don't know why Timney made it so heavy. 3lb would have been perfect. They make a good trigger, but I think they have been resting on their laurels.

Nothing Not To Like (23.06.2015)

Crisp - Zero Creep in a DPMS GII Lower (11.01.2016)

Leggi più recensioni su brownells.com

Scelti da altri clientie

WILSON COMBAT .273" (6.9MM) CENTER TO CENTER WILSON BARREL LINK
1911 BARREL LINK

WILSON COMBAT

In magazzino

CHF 15.90 *

Connettore di canna

4.8

WOLFF RUGER SP-101 KIT
17113 RUGER® SP-101® KIT

WOLFF

In magazzino

CHF 16.90 *

Kit di grippanti

PEARCE GRIP GLOCK PLUS ZERO GRIP FRAME INSERT
GRIP FRAME INSERT FOR GLOCK®

PEARCE GRIP

In magazzino

CHF 9.90 * CHF 7.53 - CHF 11.90*

Fermi per giuancette

4.1

NOVAK FIBER OPTIC FRONT SIGHT, RED, .175" HIGH, FITS KIMBER 1911
FIBER OPTIC FRONT SIGHTS RED

NOVAK

In magazzino

CHF 64.90 *

Mirini

MESA TACTICAL PRODUCTS PR 8-ROUND SHOTSHELL HOLDER FITS BENELLI M4/M1014
RECEIVER MOUNT SHOTSHELL HOLDER

MESA TACTICAL PRODUCTS

In magazzino

CHF 199.90 * CHF 109.90 - CHF 199.90*

Porta cartucce per fucile

4.5

Accesso

Hai dimenticato la password?
Registrati

SOCIAL MEDIA

Facebook

BROWNELLS.CH

CATALOGO PRODOTTI

ORDINARE

CUSTOMER SERVICE

Benvenuti!

Benvenuti su Brownells.ch, il principale rivenditore online di accessori per armi da fuoco, componenti di pistole e utensili per armaioli in Svizzera!

La nostra offerta

Se ti piace sparare, lavorare sulle armi da fuoco come artigiano o per hobby, o semplicemente possiedi un'arma, questo è il posto per te! Grazie alla nostra grande esperienza, ogni giorno, tiratori, armaioli professionisti, hobbisti, militari, esponenti delle forze dell'ordine e appassionati d'armi si rivolgono a Brownells.ch per trovare accessori e componenti di alta qualità e fare rifornimento di ciò di cui hanno bisogno.