Il Carrello è vuoto.

Carrello

0917309915

Suisse / Schweiz

Lingue: Deutsch Français Italiano

VLTOR WEAPON SYSTEMS
AR-15 GAS BLOCK LOW PROFILE

100003996

One-Piece Design Fits Under Free-Float Handguards

Slim replacement for cumbersome USGI front sight/gas block tower features a low profile for a more streamlined appearance and less chance of snagging on vegetation and other gear. Covers only 1" of barrel length and reduces weapon’s forward weight for improved handling and maneuverability. Clamp On models squeeze around the barrel with included socket head screws. Set Screw models use included set screws at the bottom of the unit to anchor the gas block to the barrel for the lowest-profile installation.

Altro...

Si inserisce un pezzo di Design sotto il flottante paramani

Sostituzione Slim per Torre ingombrante di blocco anteriore Vista/gas USGI dispone di un basso profilo per un aspetto più snella e meno possibilità di impigliamento sulla vegetazione e altri attrezzi. Copre solo 1" di lunghezza della canna e riduce il peso in avanti di arma per gestione migliorata e manovrabilità. Morsetto sui modelli spremere intorno la canna con viti incluse. Set vite modelli utilizzare viti incluse nella parte inferiore dell'unità di ancorare il blocco del gas alla canna per l'installazione di più basso profilo.

Specifiche: 17-4 PH acciaio inox, rivestimento di ossido, nero opaco. Comprende viteria testa esagonale o viti e perno di tubo gas. Tutti i modelli sono 1"(2,54 cm) lungo. Modelli disponibili per adattarsi botti con. 625" O.D. o. 750" a gas bloccare la posizione. Morsetto-sui modelli non si adattano sotto i tubi di diametro piccolo flottante o quelli con un canale di rotaia inferiore esposte all'interno del paramano come VLTOR VIS, Daniel Defense e LaRue Tactical. . 750" fissate sul -. 926 (cm 2,35) ampia, 1,388" (3.52 cm) alto. . 625" fissate sul -. 920 (cm 2.33) ampia, 1,370" (3,48 cm) alto. . 750" set vite -. 907 (cm 2,30) ampia,.1.352" (2,43 cm) alto. . 625" set vite -. 807" ampia, 1,281" alto.

Altro...

Punteggi dei clienti per VLTOR WEAPON SYSTEMS AR-15 GAS BLOCK LOW PROFILE .750 STEEL BLACK

Numero di punteggi: 12
Da brownells.com: 12
Punteggio medio: 4.1

Poor Quality Set Screws (12.02.2015)

I have a VLTOR one piece upper so I thought this would be a good match. The gas block itself looks good. Unfortunately, one of the set screws stripped when I applied minimal torque with an Allen (hex) key. The other set screw was fine. I'm not sure if this was an isolated defect, but I ended up having to drill one of the set screws out. This is very disappointing considering the slightly higher cost of the VLTOR block. To their credit Brownells' did accept this as a return.

Precision at it's Best (24.08.2015)

I compared this block first hand with seven other blocks before deciding to install the VLTOR block. The finish is superior to most; deep black phosphate and very uniform. The finish is equal to two other excellent choices, the Brownell's branded block and the Bravo Company block. The vertical grooves machined into the block add a pleasing and distinctive look and theoretically may offer some additional surface area for cooling. The machining appears very precise. Installation was straight forward and fit was tight and precise.

Nice gas block (12.07.2014)

This is a nicely done gas block but it touches my handguard (MI Gen 2 SS) very slightly at the screw heads. It is barely touching and I have checked that it is not canted, etc. Disappointing, but I will use it for another build I have planned. I usually prefer clamp on attachment, but the BCM barrel came with a dimple under the gas port so the set screw block I am replacing this with should work fine. A little filing would fix the issue, but I would rather not have to.

Less than useful (14.06.2010)

The fact the screws are on the side should have been screaming at me. It is not low profile at all, the screws protrude so far when mounted it was impossible to fit under the DD 10" Lite rail. The screws do not recess enough for proper clearance. The other version I have seen of this would fit fine as the screws are recessed and are on the bottom.

No problems (19.06.2010)

I have this installed on my SPR build which has a
White Oak Armament barrel with Midwest Industries free float handguards and everything works perfectly. My rifle cycles correctly and the bolts for the gas block has not come loose. I did however use vibra-lock on the threads.

Perfect! (07.07.2010)

After having a nasty experience with the "set screw style" gas block I decided to use a clamp on and went with the Vltor. This gas block is very well made. It was a bit tight for the gas tube to fit in which is normal and once the tube was in everything with very smoothly. Make sure to loctite the screws and this thing wil stay forever. I put this underneath my TRX Extreme which is extremely skinny. This will fit under most handguards. I don't believe this gas block is made to fit under the DD Lites and Omegas, and also the LaRues. For the handguards it is made to fit under, I'd prefer no other.

Great Low-Pro Steel Gas Block (16.01.2011)

I used this on a 16" Mid-Length Gas System AA 6.5 Grendel barrel. I have fired it in both extreme heat at 100 degrees F, down to 18 degrees F with never a malfunction using various loads. This is one of the best steel low-pro gas blocks on the market. The gas tube does fit tightly, which is a good thing for a reliable gas circuit. Loc-tite is your friend when tightening the screws after testing that you have a proper gas circuit. Read the limitations as to what handguards it will not fit under. The finish and logo are features that go above what other manufacturers offer on most of these types of products, which shows that VLTOR goes further in making a great part. Every VLTOR product I have used so far shows a higher attention to workmanship, finish, and functionality.

Super nice fit on Black Hole Weap bbl (10.08.2011)

I installed this VLTOR low profile, side clamping, gas block on a standard profile, stainless, 24 inch long, 6.8mm SPC, Black Hole Weaponry barrel. The fit was nice and snug even before I tightened the bolts. It stayed aligned while tightening. I then fit a rifle length gas tube and covered the whole set-up with a Midwest Ind. SS, 15 inch free floating hand-guard. This gas block fit underneath just fine. It fired and cycled from round one and I now have 300 rounds through the rifle without a single problem. No leaks of any gas. Alex Clark Homer, Alaska

Fits like a glove (12.08.2011)

I installed this gas block on a 0.75 inch diameter Black Hole weaponry barrel. It fit nice and snug.
The gas tube hole was nice and snug as well. After tightening I attempted to whack the gas block with a mallet to see if it would move. It did not. Now after 300 hot experimental hand-loads there is NO gas leakage. This gas block fit under a Midwest Industries SS type extended hand-guard without touching.

nice product (26.08.2011)

well made quality product. small, compact, fits right.

great piece (03.11.2013)

High value installs easy and worth every penny!

Solid but Flawed (24.08.2016)

Technically there's nothing wrong with this product. It's a solid, tightly-clamping, beautifully-fitting, streamlined gas block. The one enormous problem is that the standard hex screws it uses still have full-sized heads, heads which are (at least seemingly) in direct, if glancing, contact with the inside of my Midwest Industries MLOK guard. Now this pretty well eliminates any chance of the screws walking loose, but it also threatens the free-float nature of the guard. I so far haven't noticed an effect on accuracy, but I only run a red dot. And in addition to the 6 o'clock rail slot (or half of two of them on mine) being blocked by the bottom portion as is typical, the 4:30 and 3 o'clock slots are also unusable now on account of the screws. Lacking grip panels to guard against heat buildup, the middle 20 percent of my 15" rail is ungrip-able because of this gap. Still, if your technique allows for this or you just want a good, solid clamp design, you could definitely do worse.

Leggi più recensioni su brownells.com

109.9 109.9 1 CHF

N. prodotto: 100003996
VLTOR WEAPON SYSTEMS AR-15 GAS BLOCK LOW PROFILE .750 STEEL BLACK
Parti Fabbricante: GB2C Sostituzione Slim per Torre ingombrante di blocco anteriore Vista/gas USGI dispone di un basso profilo per un aspetto più snella e meno possibilità di impigliamento sulla vegetazione e altri attrezzi. Copre solo 1" di lunghezza della canna e riduce il peso in avanti di arma per gestione migliorata e manovrabilità. Morsetto sui modelli spremere intorno la canna con viti incluse. Set vite modelli utilizzare viti incluse nella parte inferiore dell'unità di ancorare il blocco del gas alla canna per l'installazione di più basso profilo.

109.9 CHF 2 CHF 109.90 *

Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.

Caratteristiche: Adatto per: AR-15 Diametro interno: .750 Materiale: Acciaio Tipo: Low-Profile, Morsetto

Aggiungi alla lista degli acquisti

Domande

Dettagli

Aggiungi alla lista degli acquisti

Domande

Caratteristiche

Adatto per: AR-15 Diametro interno: .750 Materiale: Acciaio Tipo: Morsetto,Low-Profile Peso della spedizione: 0.045kg Altezza di spedizione: 20mm Larghezza di spedizione: 84mm Lunghezza di spedizione: 183mm

Dettagli dell'elemento

Made in Usa
Classificazione per l'export dagli US: 0A501.x

One-Piece Design Fits Under Free-Float Handguards

Altro...

Si inserisce un pezzo di Design sotto il flottante paramani

Altro...

Punteggi dei clienti per VLTOR WEAPON SYSTEMS AR-15 GAS BLOCK LOW PROFILE .750 STEEL BLACK

Numero di punteggi: 12
Da brownells.com: 12
Punteggio medio: 4.1

Poor Quality Set Screws (12.02.2015)

Precision at it's Best (24.08.2015)

Nice gas block (12.07.2014)

Less than useful (14.06.2010)

No problems (19.06.2010)

Perfect! (07.07.2010)

Great Low-Pro Steel Gas Block (16.01.2011)

Super nice fit on Black Hole Weap bbl (10.08.2011)

Fits like a glove (12.08.2011)

nice product (26.08.2011)

well made quality product. small, compact, fits right.

great piece (03.11.2013)

High value installs easy and worth every penny!

Solid but Flawed (24.08.2016)

Leggi più recensioni su brownells.com

Scelti da altri clientie
In alternativa

MANSON PRECISION RIMLESS RIFLE CARTRIDGE, .308 WINCHESTER ROUGHER
RIMLESS RIFLE CARTRIDGES

MANSON PRECISION

In magazzino

CHF 259.90 * CHF 259.90 - CHF 459.90*

Alesatore

MAGPUL AR-15 MOE SL-K STOCK COLLAPSIBLE MIL-SPEC GRAY
AR-15 MOE SL-K STOCK COLLAPSIBLE MIL-SPEC

MAGPUL

In magazzino

CHF 64.90 *

Calci

BROWNELLS AR-15/M16 BOLT GAS RING
AR-15/M16 BOLT GAS RINGS

BROWNELLS

In magazzino

CHF 6.90 * CHF 6.90 - CHF 7.90*

YANKEE HILL MACHINE CO., INC. AR-15 GAS BLOCK ASSEMBLY LOW PROFILE .750 STEEL BLACK
AR-15 GAS BLOCK LOW PROFILE

YANKEE HILL MACHINE CO., INC.

In magazzino

CHF 29.90 * CHF 29.90 - CHF 39.90*

Gas block

3.6

BARREL CLEANER COMFORT - FOR CAL. 7.5MM - Barrel Cleaner comfort, 50 pcs. - for Cal. 7.5mm

Barrel Cleaner comfort, 50 pcs. - for Cal. 7.5mm
BARREL CLEANER COMFORT - FOR CAL. 7.5MM

VFG

Riordinato

CHF 8.90 * CHF 8.90 - CHF 31.90*

Pellets da pulizia

Accesso

Hai dimenticato la password?
Registrati

SOCIAL MEDIA

Facebook

BROWNELLS.CH

CATALOGO PRODOTTI

ORDINARE

CUSTOMER SERVICE

Benvenuti!

Benvenuti su Brownells.ch, il principale rivenditore online di accessori per armi da fuoco, componenti di pistole e utensili per armaioli in Svizzera!

La nostra offerta

Se ti piace sparare, lavorare sulle armi da fuoco come artigiano o per hobby, o semplicemente possiedi un'arma, questo è il posto per te! Grazie alla nostra grande esperienza, ogni giorno, tiratori, armaioli professionisti, hobbisti, militari, esponenti delle forze dell'ordine e appassionati d'armi si rivolgono a Brownells.ch per trovare accessori e componenti di alta qualità e fare rifornimento di ciò di cui hanno bisogno.

* Prezzi comprensivi di IVA più spedizione

Visualizzazione classica

Visualizzazione mobile