Eigenschaften
- Waffentyp: AR-15
- Versandgewicht: 0.998kg
- Versandhöhe: 84mm
- Versandbreite: 86mm
- Versandlänge: 196mm
- UPC: 050806002678
Artikel-Nr.: 080000638
050806002678 Das präzisionsgefertigte, massive Stahlwerkzeug ermöglicht es dir, die Carrier-Key-Schrauben optimal von den Seiten zu sichern, damit sie sich unter den härtesten Schnellfeuerbedingungen nicht lösen. Es beseitigt die Mühe, die Schrauben mit einem Hammer und einem Stempel zu sichern, was verrutschen und den Key, die Schrauben oder den Carrier beschädigen könnte. Das Werkzeug hält den Carrier sicher und positioniert den Key so, dass er an den richtigen Stellen eingedrückt werden kann, indem du die vier Innensechskantschrauben am Werkzeug anziehst. Eine zusätzliche Halteschraube oben am Werkzeug verhindert, dass sich der Carrier bewegt. Die Spitze dieser Schraube ist flach bearbeitet, um sicherzustellen, dass sie gleichmässigen Haltekräfte anwendet und den Carrier nicht beschädigt. Alle Schraubenspitzen sind auf Rc 58-62 gehärtet für Langlebigkeit; jedoch können Schrauben manchmal brechen, weshalb wir ein 4er-Pack Ersatzschrauben anbieten.SPECS: 1018 Kohlenstahl, schwarze Oxidbeschichtung. 3” (7,62cm) lang, 2” (5,1cm) breit, 2” hoch.
Not the best of it's type. 03.03.2016
My agency has this tool. I am a COLT LE armorer with extensive .mil and .le experience with the platform, as well as extensive personal experience and ownership. After staking four gas keys, my issues with this tool are:
1. Stakes too high on gas key. This results in very sharp edges and a questionable amount of material impinging on the screws. The staking bolts' points actually are forced higher when turning them into the gas key.
2. Staking mechanism (sharpened, hardened allen bolts) are too sharp and actually cut the metal, versus deforming it. Again, sharp edges and too little material left to impinge on screws. Further, it really destroys the finish, leaving bare metal.
3. The tool's alignment is off a bit, resulting in very slightly off-centered (versus gas key screw axis) stakes.
If you expect MilSpec-like results, IMO this is not the answer. The stakes will look amateurish and butchered, versus what is seen on a Colt factory-staked gas key. It is likely serviceable with regards to doing the job, however, and probably better (and faster) than a hammer and punch for most folks. But for serious use, look elsewhere, such as the MOAKS tools from Ned Christiansen. I have no affiliation and don't own his product at this time, but I have used it in the past with success. We chose the Brownells unit because it was easily to purchase with our existing account, but I can't recommend it to others at this time.
Note, images show a BCG that was staked 15 minutes ago. Bare metal highlights on edges are from stoning to reduce the sharp burrs from the Brownells tool, which was necessary even after light peening with a small hammer.
Excellent tool 18.11.2012
Puchased this to re-stake all of my departments long gun bolts as they had not been staked properly from the factory and the gas key had come loose on several rifles. This is a very heavy duty staking tool and I was able to stake 15 + keys with no problem. I have also used the staking points to stake other parts on the rifle such as the castle nut. Simply unscrew them and use a hammer to stake them. I highly recommend this product.
Beim Laden dieses Inhalts ist ein Fehler aufgetreten. Bitte aktualisiere die Seite, um fortzufahren. Wenn das Problem weiterhin besteht, wende dich bitte an unseren Kundenservice.