Caratteristiche
- Tipo di arma: AR-15
- Peso della spedizione: 0.998kg
- Altezza di spedizione: 84mm
- Larghezza di spedizione: 86mm
- Lunghezza di spedizione: 196mm
- UPC: 050806002678
Prezzi comprensivi di IVA più spedizione
N. prodotto: 080000638
050806002678 Strumento in acciaio solido, lavorato con precisione, che consente di fissare le viti del carrier key nel modo migliore—dai lati—per garantire che non si allentino anche nelle condizioni di fuoco rapido più estreme. Elimina il fastidio di cercare di fissare le viti con un martello e un punzone che potrebbero scivolare e danneggiare il key, le viti o il carrier. Tiene il carrier in modo sicuro e posiziona il key in modo che possa essere dimpled nei punti corretti stringendo le quattro viti esagonali dello strumento. Una vite di ritenzione aggiuntiva sulla parte superiore dello strumento impedisce al carrier di muoversi. La punta di questa vite è lavorata piatta per garantire che applichi una forza di ritenzione uniforme e non danneggi il carrier. Tutte le punte delle viti sono indurite a Rc 58-62 per la durata; tuttavia, a volte le viti possono rompersi, quindi offriamo un pacco da 4 viti di ricambio.SPECIFICHE: acciaio al carbonio 1018, finitura ossidata nera. Lunghezza 3” (7.62cm), larghezza 2” (5.1cm), altezza 2”.
Not the best of it's type. 03.03.2016
My agency has this tool. I am a COLT LE armorer with extensive .mil and .le experience with the platform, as well as extensive personal experience and ownership. After staking four gas keys, my issues with this tool are:
1. Stakes too high on gas key. This results in very sharp edges and a questionable amount of material impinging on the screws. The staking bolts' points actually are forced higher when turning them into the gas key.
2. Staking mechanism (sharpened, hardened allen bolts) are too sharp and actually cut the metal, versus deforming it. Again, sharp edges and too little material left to impinge on screws. Further, it really destroys the finish, leaving bare metal.
3. The tool's alignment is off a bit, resulting in very slightly off-centered (versus gas key screw axis) stakes.
If you expect MilSpec-like results, IMO this is not the answer. The stakes will look amateurish and butchered, versus what is seen on a Colt factory-staked gas key. It is likely serviceable with regards to doing the job, however, and probably better (and faster) than a hammer and punch for most folks. But for serious use, look elsewhere, such as the MOAKS tools from Ned Christiansen. I have no affiliation and don't own his product at this time, but I have used it in the past with success. We chose the Brownells unit because it was easily to purchase with our existing account, but I can't recommend it to others at this time.
Note, images show a BCG that was staked 15 minutes ago. Bare metal highlights on edges are from stoning to reduce the sharp burrs from the Brownells tool, which was necessary even after light peening with a small hammer.
Excellent tool 18.11.2012
Puchased this to re-stake all of my departments long gun bolts as they had not been staked properly from the factory and the gas key had come loose on several rifles. This is a very heavy duty staking tool and I was able to stake 15 + keys with no problem. I have also used the staking points to stake other parts on the rifle such as the castle nut. Simply unscrew them and use a hammer to stake them. I highly recommend this product.
Si è verificato un errore durante il caricamento di questo contenuto. Aggiorna la pagina per continuare. Se il problema persiste, contatta il nostro servizio clienti.