Brownells Svizzera - Il più grande rivenditore di componenti e accessori per armi ed attrezzistica per armieri Suisse / Schweiz
080000409
Quickly Remove Firing Pins From Remington & Ruger~ Rifles
A third hand for removing the firing pin from Remington and Ruger® bolt action rifles without lost parts or sore fingers that sometimes accompany this tricky job. Install the correct bushing for your rifle in the end of the tool body. Screw the firing pin assembly into the bushing, and tighten the threaded, steel shank to compress and capture the mainspring. The hollow shank protects the firing pin tip as it slides over the pin to compress the spring. The crosspin can then be driven out with a punch, and the spring tension relieved by gradually loosening the shank. Includes bushings for Remington 700 family and Ruger M77® Mark II rifles. Built-in storage slot holds the unused bushing on the tool body, so it’s always there when you need it. NOTE: Will not fit Ruger Left hand actions.

SPECS: Aluminum base, hardcoat anodized, black. Hardened tool steel screw shank and bushings, black oxide finish. Body - 5¼” (13.34cm) long, 1” (2.54cm) wide, 1-3⁄16" (3.02cm) high. Shank – 3½” (8.89cm) long. Fits Remington 700, 710, 721, 722, Model Seven, XP-100, M24, and 40X; Ruger M77 Mark II, 77/22, 77/17, 77/44 bolt action rifles.

139.9 139.9 1 CHF
N. prodotto: 080000409
BROWNELLS FIRING PIN REMOVAL TOOL Una terza mano per rimuovere il perno di infornamento da Remington e Ruger® Fucili bolt action senza parti perdute o dita doloranti che a volte accompagnano questo lavoro difficile. Installare la boccola corretta per il tuo fucile alla fine del corpo dell'utensile. Avvitare il gruppo percussore nella boccola e serrare il gambo filettato, acciaio per comprimere e acquisire la molla principale. Il gambo cavo protegge la punta del percussore mentre scivola sopra il perno per comprimere la molla. Il crosspin può quindi essere cacciata con un pugno, e la tensione della molla alleviato gradualmente allentando la tibia. Comprende boccole per fucili Ruger M77® Mark II e la famiglia di Remington 700. Slot di memoria incorporata tiene la boccola inutilizzata sul corpo dell'utensile, così è sempre lì quando ne avete bisogno. Nota: Le azioni di mano sinistra Ruger non è adatta.
139.9 CHF 0 CHF 139.90 *
In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.
Caratteristiche: Adatto per: Ruger, Remington Modello: Universal Rifles

Caratteristiche

Adatto per: Remington,Ruger Modello: Universal Rifles Peso della spedizione: 0.431kg Altezza di spedizione: 58mm Larghezza di spedizione: 112mm Lunghezza di spedizione: 183mm

Dettagli dell'elemento

Made in Usa



Quickly Remove Firing Pins From Remington & Ruger~ Rifles
A third hand for removing the firing pin from Remington and Ruger® bolt action rifles without lost parts or sore fingers that sometimes accompany this tricky job. Install the correct bushing for your rifle in the end of the tool body. Screw the firing pin assembly into the bushing, and tighten the threaded, steel shank to compress and capture the mainspring. The hollow shank protects the firing pin tip as it slides over the pin to compress the spring. The crosspin can then be driven out with a punch, and the spring tension relieved by gradually loosening the shank. Includes bushings for Remington 700 family and Ruger M77® Mark II rifles. Built-in storage slot holds the unused bushing on the tool body, so it’s always there when you need it. NOTE: Will not fit Ruger Left hand actions.

SPECS: Aluminum base, hardcoat anodized, black. Hardened tool steel screw shank and bushings, black oxide finish. Body - 5¼” (13.34cm) long, 1” (2.54cm) wide, 1-3⁄16" (3.02cm) high. Shank – 3½” (8.89cm) long. Fits Remington 700, 710, 721, 722, Model Seven, XP-100, M24, and 40X; Ruger M77 Mark II, 77/22, 77/17, 77/44 bolt action rifles.

Newsletter