Eigenschaften
- Hersteller/Modell: -
- Modell: -
- Versandgewicht: 0.091kg
- Versandhöhe: 8mm
- Versandbreite: 79mm
- Versandlänge: 157mm
- UPC: BOLTBODYONLY
Artikel-Nr.: 080097100
Herst.-Nr.: BOLTBODYONLY
BOLTBODYONLY Das federbelastete Werkzeug bietet konstanten, geraden Druck, um die Bolt Lugs während des Lappens mit 600 bis 800 Körnung, Siliziumkarbid-Schleifmittel, quadratisch gegen den Receiver zu halten. Es liefert bessere Ergebnisse als blosser Daumen Druck. Austauschbare Gewindesleeves passen auf die beliebten Aktionen, die unten aufgeführt sind.Das BOLT LAPPING TOOL von BROWNELLS ist ein unverzichtbares Werkzeug für jeden, der seine Waffe optimal einstellen möchte.
Das federbelastete Werkzeug sorgt für konstanten, geraden Druck, um die Bolzenlappen während des Lapens mit 600 bis 800 Körnung Siliziumkarbid-Schleifmittel quadratisch gegen den Empfänger zu halten. Es bietet bessere Ergebnisse als einfaches Daumendruck.
Die austauschbaren Schraubenzubehörteile passen zu den gängigen Aktionen, die unten aufgeführt sind.
Das M14/M1A Set enthält einen grossen Durchmesser-Plunger und einen speziellen Lapping-Griff, der für diese Modelle erforderlich ist.
Ein Gun Set enthält den Bolzenwerkzeugkörper, den Plunger und die passende Grösse des Sleeves für das aufgeführte Modell. Das M14/M1A One Gun Set enthält den Bolzenwerkzeugkörper, den grossen Durchmesser-Plunger, die passende Grösse des Sleeves und ein spezielles Sleeve sowie ein spezielles Bolzen-Lapping-Werkzeug, das nur für M14/M1A/M1 Garand geeignet ist. Das Kit enthält alle Werkzeuge, die erforderlich sind, um alle Modelle im Chart zu lapen.
Besonderer Preis, siehe unten.
Very nice fit of parts. 31.08.2015
I bought this one-gun kit after trying to use the plunger body from the M14/M1/M1A kit. It did not fit a sleeve I had bought for the Large Ring Mauser. After receiving this kit with it's plunger body I then began trying all the parts one at a time.
Both plunger bodies are 0.5620" and the sleeves are 0.5625 except the M14, it was 0.563. There were little burrs on the plunger body of the M14 kit that made me think it would not fit the different sleeves. All fit well after a little lapping.
I plan on using the bolt lug lapping tool for several rifles I am building. After using the tool I believe I can use it to square the bolt face on a Mauser Large Ring VZ-24. After reaming the sleeve from existing 9/16" to a 5/8" I will press fit a drill bushing that is 5/8 x 3/8 and use the Mason Reamer Burr which has a 3/8" shaft. The Burr has been ground to 0.3740 to 0.3745. It has a buttery slip fit in the Drill Bushing.
Mauser threads are at a 55 deg pitch and not easy to find. Brownells sells the sleeve with the right threads for the '98 and the face truing Burrs. All you need is the drill bushing, the undersized drill, and the reamer to make the altered sleeve to be able to Lapp the lugs with the original unaltered sleeve, and true the face of your bolt with your altered sleeve. After, of course, you check that the receivers threads are true to the action. This can be checked with a mandrel which Brownells has too. This can be done for any rifle that Brownells has a sleeve for. Happy Gunsmithing, JL.
Beim Laden dieses Inhalts ist ein Fehler aufgetreten. Bitte aktualisiere die Seite, um fortzufahren. Wenn das Problem weiterhin besteht, wende dich bitte an unseren Kundenservice.