Brownells Schweiz - Einer der grössten Lieferanten für Waffenteile, Büchsenmacherzubehör & Schiesssportzubehör Suisse / Schweiz

BROWNELLS
CROWN SAVER™ LATHE CENTER COVER

080000379
Your Safeguard When Turning Barrels With Finished Crowns
These brass cones take much of the anxiety out of lathe-turning a perfectly good barrel with an already finished crown. Insert a Crown Saver between the muzzle and lathe or mill center before fluting, chambering, polishing, or threading for a muzzle brake, and you can rest assured you won’t harm the rifling or ding the crown. Each brass cone is machined to within .0002" or less concentricity, making using a Crown Saver as accurate as direct barrel contact against the center. With a Crown Saver, you virtually eliminate any chance of swaging the rifling. It stays seated and will not spin in the bore when the barrel is chucked in the lathe. Small fits bores .17 to .45 caliber. Large fits bores up to .50 caliber. For best results, do not use Crown Saver more than once on barrels of the same caliber.

SPECS: 360 brass. Maximum diameter. Small - .500", Large - .750".

48.9 48.9 1 CHF
Artikel-Nr.: 080000379
BROWNELLS CROWN SAVER LATHE CENTER COVER SMALL 10 PACK
Herstellerproduktnummer: 080000379 Diese Messingkegel nehmen dem Drehen eines einwandfreien Laufs mit bereits fertiggestellter Krone einen Grossteil der Angst ab. Setzen Sie einen Crown Saver zwischen die Mündung und die Dreh- oder Fräsmitte ein, bevor Sie eine Mündungsbremse rillen, kammern, polieren oder einfädeln. Sie können sicher sein, dass Sie das Gewehr oder die Krone nicht beschädigen. Jeder Messingkegel ist bis zu einer Rundlaufgenauigkeit von 0,0002 Zoll oder weniger bearbeitet, sodass ein Crown Saver so genau wie ein direkter Laufkontakt mit der Mitte ist. Mit einem Crown Saver verhindern Sie praktisch, dass das Gewehr verpresst wird. Er bleibt sitzen und wird es nicht tun Drehen Sie in der Bohrung, wenn der Lauf in der Drehmaschine eingespannt ist. Klein für Bohrungen mit Kaliber .17 bis .45. Gross für Bohrungen mit Kaliber .50. Verwenden Sie Crown Saver nicht mehr als einmal für Läufe desselben Kalibers .
48.9 CHF 0 CHF 48.90 *
Nachbestellt, Lieferzeit ca. 4-12 Wochen aus dem Lager USA.

Eigenschaften

Versandgewicht: 0.045kg Versandbreite: 83mm Versandlänge: 146mm

Artikeldetails

Made in USA



Your Safeguard When Turning Barrels With Finished Crowns
These brass cones take much of the anxiety out of lathe-turning a perfectly good barrel with an already finished crown. Insert a Crown Saver between the muzzle and lathe or mill center before fluting, chambering, polishing, or threading for a muzzle brake, and you can rest assured you won’t harm the rifling or ding the crown. Each brass cone is machined to within .0002" or less concentricity, making using a Crown Saver as accurate as direct barrel contact against the center. With a Crown Saver, you virtually eliminate any chance of swaging the rifling. It stays seated and will not spin in the bore when the barrel is chucked in the lathe. Small fits bores .17 to .45 caliber. Large fits bores up to .50 caliber. For best results, do not use Crown Saver more than once on barrels of the same caliber.

SPECS: 360 brass. Maximum diameter. Small - .500", Large - .750".

Newsletter