The Dead Level levels your reticle in relation to the Earth taking out any margin of error of the reticle not being perfectly level with the scope body. Simply attach your mounted scope to the Dead Level, level the device with the precision thumbscrews to center up the bulls-eye level, then just level the reticle with a predetermined level line or plumb bob. Aluminum Mil. Spec. Now features an Anodized Hard Coat Type III in a crimson and black finish. Instructions included. FOR USE WITH MIL STD 1913 PICATINNY COMPLIANT RINGS AND MOUNTS
Plus...
La mort niveau niveaux votre réticule par rapport à la terre en prenant une marge d’erreur du réticule ne étant pas parfaitement de niveau avec le corps de la portée. Attachez simplement votre lunette montée au niveau morts, niveau de l’appareil avec les vis de serrage de précision pour centrer au niveau du point de mire, puis juste niveau le réticule avec une ligne de niveau prédéterminé ou un fil à plomb. Mil en aluminium. Spec. Dispose désormais d’un anodisé dur manteau Type III dans une finition noire et pourpre. Instructions fournies. POUR UNE UTILISATION AVEC MIL STD 1913 PICATINNY COMPATIBLE AVEC ANNEAUX ET SUPPORTS
Plus...
Évaluations client de BADGER ORDNANCE DEAD LEVEL SCOPE LEVELING DEVICE
Nombre d'évaluations: 2
De brownells.com: 2
Note moyenne: 4.5
Excellent Tool(04.11.2013)
This tool is excellent at getting your scope perfectly level and tightening the scope in the rings. When shooting long range competitions it is important to dial in elevation from 200 to 1000 yards and not have windage drift. It is a bit expensive, but well worth it. Very solidly built. Will last a lifetime.
Good but not perfect(25.10.2014)
Pros:
Once I attached a set of rings to the rail, mounted the
scope a little loosely in the rings & levelled the base, it
was a quick job to level the reticle by looking through the
scope at a reference line from a self leveling laser level
line projected on the wall, rotating the scope until the
reticle matched the laser line, tightening down the rings
and rechecking the alignment.
Cons:
I found the integral bubble level hard to get centered so I
had to use another level to get the base level.
Because of the length of the rail, low rings don't work
well with it unless risers are added. A shorter rail would
Référence: 093000051 BADGER ORDNANCE DEAD LEVEL SCOPE LEVELING DEVICE Ref Fabricant: 20050 La mort niveau niveaux votre réticule par rapport à la terre en prenant une marge d’erreur du réticule ne étant pas parfaitement de niveau avec le corps de la portée. Attachez simplement votre lunette montée au niveau morts, niveau de l’appareil avec les vis de serrage de précision pour centrer au niveau du point de mire, puis juste niveau le réticule avec une ligne de niveau prédéterminé ou un fil à plomb. Mil en aluminium. Spec. Dispose désormais d’un anodisé dur manteau Type III dans une finition noire et pourpre. Instructions fournies. POUR UNE UTILISATION AVEC MIL STD 1913 PICATINNY COMPATIBLE AVEC ANNEAUX ET SUPPORTS
284.9CHF18CHF 284.90
*
Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.
The Dead Level levels your reticle in relation to the Earth taking out any margin of error of the reticle not being perfectly level with the scope body. Simply attach your mounted scope to the Dead Level, level the device with the precision thumbscrews to center up the bulls-eye level, then just level the reticle with a predetermined level line or plumb bob. Aluminum Mil. Spec. Now features an Anodized Hard Coat Type III in a crimson and black finish. Instructions included. FOR USE WITH MIL STD 1913 PICATINNY COMPLIANT RINGS AND MOUNTS
Plus...
La mort niveau niveaux votre réticule par rapport à la terre en prenant une marge d’erreur du réticule ne étant pas parfaitement de niveau avec le corps de la portée. Attachez simplement votre lunette montée au niveau morts, niveau de l’appareil avec les vis de serrage de précision pour centrer au niveau du point de mire, puis juste niveau le réticule avec une ligne de niveau prédéterminé ou un fil à plomb. Mil en aluminium. Spec. Dispose désormais d’un anodisé dur manteau Type III dans une finition noire et pourpre. Instructions fournies. POUR UNE UTILISATION AVEC MIL STD 1913 PICATINNY COMPATIBLE AVEC ANNEAUX ET SUPPORTS
Plus...
Évaluations client de BADGER ORDNANCE DEAD LEVEL SCOPE LEVELING DEVICE
Nombre d'évaluations: 2
De brownells.com: 2
Note moyenne: 4.5
Excellent Tool(04.11.2013)
This tool is excellent at getting your scope perfectly level and tightening the scope in the rings. When shooting long range competitions it is important to dial in elevation from 200 to 1000 yards and not have windage drift. It is a bit expensive, but well worth it. Very solidly built. Will last a lifetime.
Good but not perfect(25.10.2014)
Pros:
Once I attached a set of rings to the rail, mounted the
scope a little loosely in the rings & levelled the base, it
was a quick job to level the reticle by looking through the
scope at a reference line from a self leveling laser level
line projected on the wall, rotating the scope until the
reticle matched the laser line, tightening down the rings
and rechecking the alignment.
Cons:
I found the integral bubble level hard to get centered so I
had to use another level to get the base level.
Because of the length of the rail, low rings don't work
well with it unless risers are added. A shorter rail would