EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Leupold DeltaPoint Pro, JPoint, Redfield Accelerator, or Optima red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits: Elite Stock II with adjustable (LPA/Bomar style, shown above) rear sight Elite Stock III with adjustable (LPA/Bomar style, shown above) rear sight Hunter with adjustable (LPA/Bomar style, shown above) rear sight Limited Custom with adjustable (LPA/Bomar style, shown above) rear sight Limited Custom Xtreme with adjustable (LPA/Bomar style, shown above) rear sight Match Elite with adjustable (LPA/Bomar style, shown above) rear sight Match Xtreme with adjustable (LPA/Bomar style, shown above) rear sight P Match with adjustable (LPA/Bomar style, shown above) rear sight P Match Pro with adjustable (LPA/Bomar style, shown above) rear sight Stock II Xtreme with adjustable (LPA/Bomar style, shown above) rear sight Stock III Xtreme with adjustable (LPA/Bomar style, shown above) rear sight This mount does not fit: EAA / Tanfoglio Witness with fixed rear sight EAA / Tanfoglio Witness with Novak style adjustable rear sight, shown above
Mount per il mirino EAA SUPER SIGHT per Leupold DeltaPoint Pro
I mirini red dot EGW sono progettati per essere installati da sinistra a destra (con la volata rivolta in avanti). Il sistema a dente di sega presenta un taper progressivo per facilitare l'installazione.
Basta rimuovere il mirino posteriore della tua arma e sostituirlo con il montaggio EGW per montare il tuo Leupold DeltaPoint Pro, JPoint, Redfield Accelerator o mirino red dot Optima. Puoi rimuovere il montaggio e ripristinare il tuo mirino posteriore in qualsiasi momento. Hardware di montaggio incluso.
Istruzioni di Installazione
- Rimuovere il mirino posteriore*
- Installare il montaggio EGW nel dente di sega
- Serrare la vite di fissaggio (se applicabile)
- Posizionare il mirino red dot sul montaggio EGW (mettere un piccolo pezzo di carta tra il mirino red dot e il montaggio faciliterà la rimozione e terrà il Loctite lontano dal mirino red dot.)
- Applicare Loctite blu alle viti di montaggio fornite
- Serrare le viti di montaggio a 15in/lbs
La modifica della tua arma potrebbe annullare la garanzia del produttore. Questo prodotto dovrebbe essere installato e controllato da un armaiolo qualificato. Non si assume alcuna responsabilità per danni o lesioni che possono derivare da un'installazione o uso improprio di questo prodotto.
Questo montaggio si adatta a:
- Elite Stock II con mirino posteriore regolabile (stile LPA/Bomar, mostrato sopra)
- Elite Stock III con mirino posteriore regolabile (stile LPA/Bomar, mostrato sopra)
- Hunter con mirino posteriore regolabile (stile LPA/Bomar, mostrato sopra)
- Limited Custom con mirino posteriore regolabile (stile LPA/Bomar, mostrato sopra)
- Limited Custom Xtreme con mirino posteriore regolabile (stile LPA/Bomar, mostrato sopra)
- Match Elite con mirino posteriore regolabile (stile LPA/Bomar, mostrato sopra)
- Match Xtreme con mirino posteriore regolabile (stile LPA/Bomar, mostrato sopra)
- P Match con mirino posteriore regolabile (stile LPA/Bomar, mostrato sopra)
- P Match Pro con mirino posteriore regolabile (stile LPA/Bomar, mostrato sopra)
- Stock II Xtreme con mirino posteriore regolabile (stile LPA/Bomar, mostrato sopra)
- Stock III Xtreme con mirino posteriore regolabile (stile LPA/Bomar, mostrato sopra)
Questo montaggio non si adatta a:
- EAA / Tanfoglio Witness con mirino posteriore fisso
- EAA / Tanfoglio Witness con mirino posteriore regolabile stile Novak, mostrato sopra