This mount is NOT a drop in part and will require fitting. EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. EGW products should be installed and checked by a qualified and competent gunsmith. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail after checking for fit Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits: Firearms with oversized Novak cut dovetails. This mount is made .007"" larger than a standard Novak cut and will require fitting.
Entdecke die perfekte Lösung für deine Vortex Viper/Venom!
Die OVERSIZED NOVAK 0.007" VORTEX VIPER/VENOM SIGHT MOUNT von EGW ist die ideale Montage für deine Vortex Viper oder Venom. Beachte, dass diese Montage kein Drop-in-Teil ist und eine Anpassung erfordert.
Produktbeschreibung
EGW Rotpunktvisiere sind so konzipiert, dass sie von links nach rechts (mit dem Mündungsende nach vorne) installiert werden. Der Dovetail hat eine progressive Verjüngung, um die Installation zu erleichtern. Entferne einfach das hintere Visier deines Gewehrs und ersetze es durch die EGW-Montage, um dein Vortex Viper/Venom, Burris FastFire oder Docter Rotpunktvisier zu montieren. Du kannst die Montage jederzeit abnehmen und dein hinteres Visier wieder anbringen.
Installationsanleitung
- Entferne das hintere Visier*
- Installiere die EGW Sight Mount im Dovetail nach Überprüfung der Passform
- Ziehe die Set-Schraube fest (falls zutreffend)
- Platziere das Rotpunktvisier auf der EGW Sight Mount (ein kleines Stück Papier zwischen dem Rotpunktvisier und der Montage erleichtert die Entfernung und hält Loctite vom Rotpunktvisier fern)
- Trage blauen Loctite auf die mitgelieferten Montageschrauben auf
- Ziehe die Montageschrauben mit 15in/lbs an
Mitgeliefertes Montagematerial:
- 2 Button Head Cap Schrauben - für Vortex Viper und Venom Sights
- 2 Flat Head Cap Schrauben - für Burris FastFire und Docter Sights
Die mit dieser Montage gelieferten Schrauben erfordern einen 5/64'' Inbusschlüssel für die Installation. Beachte, dass Modifikationen an deinem Feuerwaffen die Herstellergarantie ungültig machen können.
Dieses Produkt sollte von einem qualifizierten Gunsmith installiert und überprüft werden. Es wird keine Haftung für Schäden oder Verletzungen übernommen, die aus unsachgemässer Installation oder Verwendung dieses Produkts resultieren können.
Kompatibilität
Diese Montage passt auf Feuerwaffen mit oversized Novak cut Dovetails. Diese Montage ist .007" grösser als ein Standard-Novak-Cut und erfordert eine Anpassung.