This mount is NOT a drop in part and will require fitting. EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. EGW products should be installed and checked by a qualified and competent gunsmith. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail after checking for fit Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits: Firearms with oversized Novak cut dovetails. This mount is made .007"" larger than a standard Novak cut and will require fitting.
Montage de visée OVERSIZED NOVAK pour Vortex Viper/Venom
Ce montage n'est pas une pièce à installer directement et nécessitera un ajustement. Les viseurs à point rouge EGW sont conçus pour être installés de gauche à droite (avec le canon orienté vers l'avant). Le rail a un profil progressif pour faciliter l'installation.
Il te suffit de retirer la hausse arrière de ton arme et de la remplacer par le montage EGW afin de pouvoir installer ton viseur à point rouge Vortex Viper/Venom, Burris FastFire ou Docter. Tu peux retirer le montage et remettre ta hausse arrière à tout moment. Le matériel de montage est inclus.
Instructions d'installation :
- Retire la hausse arrière*
- Installe le montage de visée EGW dans le rail après avoir vérifié l'ajustement
- Serre la vis de réglage (si applicable)
- Place le viseur à point rouge sur le montage EGW (placer un petit morceau de papier entre le viseur et le montage facilitera le retrait et empêchera le Loctite de toucher le viseur)
- Applique du Loctite bleu sur les vis de montage fournies
- Serre les vis de montage à 15 in/lbs
Vis de montage incluses :
- 2 vis à tête bombée - fournies pour les viseurs Vortex Viper et Venom
- 2 vis à tête plate - fournies pour les viseurs Burris FastFire et Docter
Les vis incluses avec ce montage nécessitent une clé Allen de 5/64'' pour l'installation. La modification de ton arme à feu peut annuler la garantie du fabricant. Ce produit doit être installé et vérifié par un armurier qualifié.
Aucune responsabilité n'est exprimée ou implicite pour les dommages ou blessures pouvant résulter d'une installation ou d'une utilisation incorrecte de ce produit.
Ce montage s'adapte à :
Les armes à feu avec des rails Novak coupés surdimensionnés. Ce montage est fabriqué .007" plus grand qu'un rail Novak standard et nécessitera un ajustement.