Fully-machined hardened steel mount with three-point mounting, provides a stable, secure base for mounting large objective scopes. Easily clamps to the charger guide dovetail and receiver mount lug without modifications to rifle. Heavy, forward locking screw gives rock solid stability at the receiver ring. Sight channel allows back-up use of iron sights without removing scope.
Monte acciaio indurito completamente lavorati con tre punti di fissaggio, fornisce una base stabile e sicura per grandi ambiti oggettivi di montaggio. Fascette facilmente al caricabatterie guida a coda di rondine e ricevitore Monte lug senza modifiche al fucile. Pesante, vite di bloccaggio avanti dà stabilità solida roccia all'anello del ricevitore. Vista canale consente backup utilizzo delle viste del ferro senza rimuovere il campo di applicazione. Weaver ha guida superiore stile Weaver. Picatinny utilizza una guida Picatinny per vista aggiunta opzioni di montaggio. 7" Picatinny - esteso, lunghezza 7" sistema ferroviario Picatinny consente di utilizzare molte opzioni di montaggio di vista. Tactical dispone di una guida Picatinny ma senza il canale vista aperta. Assolutamente la t può dare sotto la coppia di serraggio più stretti. Tutti accettano di anelli stile Weaver.
Specifiche: 4140 acciaio, nero, rivestimento di nitruro. Induriti per Rc 60-62. 5,38"(13,6 cm) lungo. 1,875"(4,7 cm) alta. Pesa 10,9 oz (310 g). 7" Picatinny - 7" (17,7 cm) lungo, 1,85 cm (4.7) alti. Pesa 15,3 oz (435g).
Altro...
Punteggi dei clienti per SMITH ENTERPRISE M14 SCOPE MOUNT
Numero di punteggi: 3
Da brownells.com: 3
Punteggio medio: 3.3
Should have bought a Sadlak.(14.11.2010)
I've been trying to get this mount to work for over 3 yrs. Shoots 20" high with MK IV scope adjusted to full down limit (that's 45 minutes down from mechanical center). Tried different rings (Smith, Burris Signature), adding shims between rings and mount, raising front of mount with forward setscrew. Shoots groups under 1" @ 100yds when installed per instructions with Smith rings, but 20" high. Shot like a shotgun (6" groups) with other attempts to lower point of impact. Mount manufacturer said SA, NM, M1A not manufactured to tolerance. It groups under an inch! Should have bought a Sadlak.
One of the Best Mounts for M1A/M14(16.12.2010)
This is a good Mount. A little more difficult to install than a regular mount like bolt guns but this is due to the nature of the M14. Sadlak and Smith Enterprise are very much alike if not exactly. The Mounts are manufactured to G.I. receiver specs. I have installed these on many M14's in Iraq. But some Springfield's Receivers are not to G.I. specs. You can send the rifle to Smith Enterprise or another competent gunsmith who is good with these style of rifles. I would recommend this mount wholeheartedly. I've never had problems with it that could not be overcame.
Rock Solid(09.08.2012)
Great mount, not the easiest to install but well worth the time and money. Before trying to put it on - Read the instructions!
N. prodotto: 851000001 SMITH ENTERPRISE M14 SCOPE MOUNT Parti Fabbricante: 2006 Monte acciaio indurito completamente lavorati con tre punti di fissaggio, fornisce una base stabile e sicura per grandi ambiti oggettivi di montaggio. Fascette facilmente al caricabatterie guida a coda di rondine e ricevitore Monte lug senza modifiche al fucile. Pesante, vite di bloccaggio avanti dà stabilità solida roccia all'anello del ricevitore. Vista canale consente backup utilizzo delle viste del ferro senza rimuovere il campo di applicazione. Weaver ha guida superiore stile Weaver. Picatinny utilizza una guida Picatinny per vista aggiunta opzioni di montaggio. 7" Picatinny - esteso, lunghezza 7" sistema ferroviario Picatinny consente di utilizzare molte opzioni di montaggio di vista. Tactical dispone di una guida Picatinny ma senza il canale vista aperta. Assolutamente la t può dare sotto la coppia di serraggio più stretti. Tutti accettano di anelli stile Weaver.
539.9CHF6CHF 539.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
Caratteristiche:Adatto per: SpringfieldColore: BlackMateriale: AcciaioModello: M14, M1ANumero di basi: 1 pezzoTipo: Basi tattiche
Adatto per:
Springfield
Colore:
Black
Materiale:
Acciaio
Modello:
M14,M1A
Numero di basi:
1 pezzo
Tipo:
Basi tattiche
Peso della spedizione: 0.363kgAltezza di spedizione: 41mmLarghezza di spedizione: 91mmLunghezza di spedizione: 165mm
Fully-machined hardened steel mount with three-point mounting, provides a stable, secure base for mounting large objective scopes. Easily clamps to the charger guide dovetail and receiver mount lug without modifications to rifle. Heavy, forward locking screw gives rock solid stability at the receiver ring. Sight channel allows back-up use of iron sights without removing scope.
Monte acciaio indurito completamente lavorati con tre punti di fissaggio, fornisce una base stabile e sicura per grandi ambiti oggettivi di montaggio. Fascette facilmente al caricabatterie guida a coda di rondine e ricevitore Monte lug senza modifiche al fucile. Pesante, vite di bloccaggio avanti dà stabilità solida roccia all'anello del ricevitore. Vista canale consente backup utilizzo delle viste del ferro senza rimuovere il campo di applicazione. Weaver ha guida superiore stile Weaver. Picatinny utilizza una guida Picatinny per vista aggiunta opzioni di montaggio. 7" Picatinny - esteso, lunghezza 7" sistema ferroviario Picatinny consente di utilizzare molte opzioni di montaggio di vista. Tactical dispone di una guida Picatinny ma senza il canale vista aperta. Assolutamente la t può dare sotto la coppia di serraggio più stretti. Tutti accettano di anelli stile Weaver.
Specifiche: 4140 acciaio, nero, rivestimento di nitruro. Induriti per Rc 60-62. 5,38"(13,6 cm) lungo. 1,875"(4,7 cm) alta. Pesa 10,9 oz (310 g). 7" Picatinny - 7" (17,7 cm) lungo, 1,85 cm (4.7) alti. Pesa 15,3 oz (435g).
Altro...
Punteggi dei clienti per SMITH ENTERPRISE M14 SCOPE MOUNT
Numero di punteggi: 3
Da brownells.com: 3
Punteggio medio: 3.3
Should have bought a Sadlak.(14.11.2010)
I've been trying to get this mount to work for over 3 yrs. Shoots 20" high with MK IV scope adjusted to full down limit (that's 45 minutes down from mechanical center). Tried different rings (Smith, Burris Signature), adding shims between rings and mount, raising front of mount with forward setscrew. Shoots groups under 1" @ 100yds when installed per instructions with Smith rings, but 20" high. Shot like a shotgun (6" groups) with other attempts to lower point of impact. Mount manufacturer said SA, NM, M1A not manufactured to tolerance. It groups under an inch! Should have bought a Sadlak.
One of the Best Mounts for M1A/M14(16.12.2010)
This is a good Mount. A little more difficult to install than a regular mount like bolt guns but this is due to the nature of the M14. Sadlak and Smith Enterprise are very much alike if not exactly. The Mounts are manufactured to G.I. receiver specs. I have installed these on many M14's in Iraq. But some Springfield's Receivers are not to G.I. specs. You can send the rifle to Smith Enterprise or another competent gunsmith who is good with these style of rifles. I would recommend this mount wholeheartedly. I've never had problems with it that could not be overcame.
Rock Solid(09.08.2012)
Great mount, not the easiest to install but well worth the time and money. Before trying to put it on - Read the instructions!