Eigenschaften
- Modell: 870
- Waffentyp: Remington
- Versandgewicht: 0.045kg
- Versandhöhe: 5mm
- Versandbreite: 84mm
- Versandlänge: 188mm
- UPC: 050806105294
Artikel-Nr.: 080612000
Herst.-Nr.: RIVETSTAKTOOL
050806105294 Zwei speziell geschliffene Stempel machen das Anpassen der 870 Auswerferfeder und des Gehäuses auf Remingtons einzigartiger 2-Stufen-Niete zum Kinderspiel! Das Loch in der Vorderseite des Werkzeugs #1 ermöglicht es dir, das Auswerfergehäuse mit dem unteren Teil der Niete am Empfänger zu befestigen. Das Werkzeug #2 wird dann verwendet, um die Auswerferfeder im Auswerfergehäuse mit dem oberen Teil der Niete zu sichern. Das Deluxe-Kit kombiniert die beiden oben genannten Stempel mit einem Nieten-Schneider für die Auswerferfeder, der es dir ermöglicht, nur den verformten Bereich der vorderen Niete zu entfernen. Oft kannst du die bestehende Niete erneut verformen.Mit zwei speziell geschliffenen Stempeln wird das Anpassen der 870 Ejektorfeder und des Gehäuses auf den einzigartigen 2-Stufen-Rivets von Remington zum Kinderspiel! Das Loch in der Vorderseite des Werkzeugs #1 ermöglicht es dir, das Ejektorgehäuse mit dem unteren Teil des Rivets am Empfänger zu befestigen. Das Werkzeug #2 wird dann verwendet, um die Ejektorfeder im Ejektorgehäuse mit dem oberen Teil des Rivets zu sichern.
Das Deluxe-Kit kombiniert die beiden oben genannten Stempel mit einem Ejektorfeder-Rivet-Cutter, der es dir ermöglicht, nur den verformten Bereich des vorderen Rivets abzutrennen. Oft kannst du so den bestehenden Rivet wieder verformen.
Just use a Home Depot punch 01.08.2018
Bought this set to replace the ejector and ejector spring on my 870. After reading reviews, I was hesitant to buy but couldn't find any other tools on the market so I went ahead and bought this set. The tool for the rear rivet cracked down both sides and did not seat the rivet tight enough. I ended up using a standard punch to flatten the rivet. The tool for the front rivet didn't even fit inside the ejector. After some work with a Dremel tool I got the punch to fit and managed to hammer the first level of the front rivet flat. To flatten the second level of the front rivet I again used a standard punch since at this point the Brownell's punch was cracked.
The only reason this gets a 2 star review is that after calling Brownell's, they refunded my money. 5 stars for customer service, 1 star for the tool set.
Did the job. Once. 11.05.2018
I had made my own rivet stakes when I first replaced the ejector and spring (2-3/4 to 3" conversion) out of some hardened bolts (grade 5, maybe grade 8 would have worked better), but messed up the job and damaged my stakes. Decided to order this set along with new rivets because I didn't feel like fixing the stakes I made.
The stake with the large hole was useless. It didn't set the rear rivet at all, just mushroomed it a bit and didn't go down far enough to actually lock the ejector in place. I ended up using the flat side of the other stake to set the rear rivet and that worked just fine.
The stake with the small hole worked for the first stage of the front rivet, but the hole is so tight that after setting the rivet I had to clamp the stake in a vice and gently tap the receiver with a mallet to get the stake off the second stage of the front rivet. All while trying not to break it off. Very annoying. I ended up setting the second stage of the front rivet with a small punch from my regular punch set.
After setting the first stage of the front rivet the stake was deformed to the point that I would not be able to use it a second time.
I gave it two stars instead of one because the one stake does work for the two stage front rivet, but it was a one chance deal as the tool is now useless. Don't buy this if you want to add it to your tool set.
Beim Laden dieses Inhalts ist ein Fehler aufgetreten. Bitte aktualisiere die Seite, um fortzufahren. Wenn das Problem weiterhin besteht, wende dich bitte an unseren Kundenservice.