Lightens trigger pull and cocking effort for fast, accurate shooting. Open center retains durability of factory spring, gives consistent, uniform, spring tension.
SPECS: Spring steel. Colt/EMF fits Colt Cowboy and Single Action Army, EMF Hartford. Uberti fits private-label, SAA clones made by Uberti. May require minor fitting.
Altro...
Design unico azione leviga, riduce Trigger Pull
Alleggerisce il tiro di innesco e sforzo d'armamento per il tiro veloce, accurato. Centro aperto mantiene la durevolezza della molla di fabbrica, dà tensione costante, uniforme, primavera.
Specifiche: acciaio della molla. Colt/EMF si inserisce Colt Cowboy e singola azione armata, EMF Hartford. Uberti si inserisce private label, cloni SAA fatti da Uberti. Possono richiedere il minore adattamento.
Altro...
Punteggi dei clienti per WOLFF UBERTI MAINSPRING
Numero di punteggi: 3
Da brownells.com: 3
Punteggio medio: 3.7
Just Right(09.07.2013)
At first, I tried the Lee Gunslinger spring set in my 3rd generation Colt SAA which is chambered in 45 Colt. The springs made the action feel sweet but light primer hits were a problem with the Remington large pistol primers I use. I ordered the Wolff mainspring and kept the wire trigger spring from the Lee set. I think I have a great combination now as the hammer is still lighter to pull than with the factory spring and the gun feels very "slick". I love the feel of my Colt SAA with the Wolff mainspring. It installed easily without any fitting and ordering from Brownell's is always a pleasure.
Also works in an Uberti 1858 Remington(22.10.2013)
I bought this spring for use with a Taylor's conversion cylinder. It fit my Uberti Remington perfectly. The action is much smoother, and the cylinder's firing pins are no longer getting battered.
WILL NOT FIT my EMF !!!(08.06.2015)
I ordered this for an EMF Hartford 45 Colt. There was an obvious problem as the length was way too short ! The overall length falls between the factory spring and the length of a factory
N. prodotto: 969322850 WOLFF UBERTI MAINSPRING Parti Fabbricante: 32285 Alleggerisce il tiro di innesco e sforzo d'armamento per il tiro veloce, accurato. Centro aperto mantiene la durevolezza della molla di fabbrica, dà tensione costante, uniforme, primavera.
19.9CHF0CHF 19.90
*
In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.
Adatto per:
Uberti
Modello:
1873
Peso della spedizione: 0.009kgAltezza di spedizione: 8mmLarghezza di spedizione: 66mmLunghezza di spedizione: 117mm
Dettagli dell'elemento
Made in Usa
N. prodotto: 969322800 WOLFF COLT/EMF MAINSPRING Parti Fabbricante: 32280 Alleggerisce il tiro di innesco e sforzo d'armamento per il tiro veloce, accurato. Centro aperto mantiene la durevolezza della molla di fabbrica, dà tensione costante, uniforme, primavera.
19.9CHF32CHF 19.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
Caratteristiche:Adatto per: ColtModello: Single Action Army
Lightens trigger pull and cocking effort for fast, accurate shooting. Open center retains durability of factory spring, gives consistent, uniform, spring tension.
SPECS: Spring steel. Colt/EMF fits Colt Cowboy and Single Action Army, EMF Hartford. Uberti fits private-label, SAA clones made by Uberti. May require minor fitting.
Altro...
Design unico azione leviga, riduce Trigger Pull
Alleggerisce il tiro di innesco e sforzo d'armamento per il tiro veloce, accurato. Centro aperto mantiene la durevolezza della molla di fabbrica, dà tensione costante, uniforme, primavera.
Specifiche: acciaio della molla. Colt/EMF si inserisce Colt Cowboy e singola azione armata, EMF Hartford. Uberti si inserisce private label, cloni SAA fatti da Uberti. Possono richiedere il minore adattamento.
Altro...
Punteggi dei clienti per WOLFF UBERTI MAINSPRING
Numero di punteggi: 3
Da brownells.com: 3
Punteggio medio: 3.7
Just Right(09.07.2013)
At first, I tried the Lee Gunslinger spring set in my 3rd generation Colt SAA which is chambered in 45 Colt. The springs made the action feel sweet but light primer hits were a problem with the Remington large pistol primers I use. I ordered the Wolff mainspring and kept the wire trigger spring from the Lee set. I think I have a great combination now as the hammer is still lighter to pull than with the factory spring and the gun feels very "slick". I love the feel of my Colt SAA with the Wolff mainspring. It installed easily without any fitting and ordering from Brownell's is always a pleasure.
Also works in an Uberti 1858 Remington(22.10.2013)
I bought this spring for use with a Taylor's conversion cylinder. It fit my Uberti Remington perfectly. The action is much smoother, and the cylinder's firing pins are no longer getting battered.
WILL NOT FIT my EMF !!!(08.06.2015)
I ordered this for an EMF Hartford 45 Colt. There was an obvious problem as the length was way too short ! The overall length falls between the factory spring and the length of a factory