Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780 Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR This mount will fit: Smith & Wesson M&P Full Size Smith & Wesson M&P 2.0 Full Size Smith & Wesson M&P 22 Full Size Smith & Wesson M&P Compact* Smith & Wesson M&P 2.0 Compact* Smith & Wesson SD9VE Smith & Wesson SD40VE This mount does not fit: Smith & Wesson M&P Shield (Our mount is too wide to fit the Shield) Smith & Wesson M&P Shield EZ .380 Smith & Wesson SW9VE Smith & Wesson SW40VE Smith & Wesson M&P C.O.R.E Series *Will not fit the M&P .22 Compact. Smith and Wesson's rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering.These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs *Rear sight pusher tool highly recommended*
Entdecke die perfekte Montage für dein Trijicon RMR Rotpunktvisier!
Die S&W M&P TRIJICON RMR SIGHT MOUNT von EGW ist die ideale Lösung, um dein Trijicon RMR Rotpunktvisier auf deiner Waffe zu montieren. Diese Halterung ist aus hochwertigem 7075 Aluminium gefertigt und mit einer mattschwarzen Hartbeschichtung versehen.
Produktdetails:
- Material: 7075 Aluminium
- Beschichtung: Matte Black Hardcoat
- Gesamtlänge: 1.780"
- Gesamtbreite: 1.1"
- Befestigungsmaterial: (2) 6-32 Flachkopfschrauben, (1) 6-32 X 3/16 Set-Schraube
- Rotpunkt-Kompatibilität: Trijicon RMR
Diese Halterung passt auf:
- Smith & Wesson M&P Full Size
- Smith & Wesson M&P 2.0 Full Size
- Smith & Wesson M&P 22 Full Size
- Smith & Wesson M&P Compact*
- Smith & Wesson M&P 2.0 Compact*
- Smith & Wesson SD9VE
- Smith & Wesson SD40VE
Diese Halterung passt nicht auf:
- Smith & Wesson M&P Shield (Unsere Halterung ist zu breit für die Shield)
- Smith & Wesson M&P Shield EZ .380
- Smith & Wesson SW9VE
- Smith & Wesson SW40VE
- Smith & Wesson M&P C.O.R.E Serie
*Passt nicht auf die M&P .22 Compact. Die Dovetails der Rücksicht von Smith & Wesson können in den Abmessungen variieren. Unsere Halterungen werden nach denselben Toleranzen gefertigt. Einige Benutzer könnten Schwierigkeiten haben, unsere Platte auf ihrem Schlitten zu installieren, aufgrund der variierenden Toleranzen. Bitte beachte dies bei deiner Bestellung.
Diese Halterungen sollten von einem qualifizierten Büchsenmacher installiert und überprüft werden. Es wird keine Haftung für Schäden oder Verletzungen übernommen, die aus unsachgemässer Installation oder Verwendung dieses Produkts resultieren können.
Um dein Trijicon RMR Rotpunktvisier zu montieren, entferne einfach die Rücksicht deiner Waffe und ersetze sie durch unsere Halterung. Es sind keine Änderungen erforderlich. Du kannst unsere Halterung jederzeit abnehmen und deine Rücksicht wieder anbringen. Befestigungsmaterial ist im Lieferumfang enthalten.
Installationsanleitung:
- Entferne die Rücksicht*
- Installiere die EGW Sight Mount im Dovetail
- Ziehe die Set-Schraube an (falls zutreffend)
- Platziere das Rotpunktvisier auf der EGW Sight Mount (ein kleines Stück Papier zwischen dem Rotpunktvisier und der Halterung erleichtert die Entfernung und hält Loctite vom Rotpunktvisier fern.)
- Trage blauen Loctite auf die mitgelieferten Befestigungsschrauben auf
- Ziehe die Befestigungsschrauben auf 15 in/lbs an
*Rücksicht-Pusher-Werkzeug wird dringend empfohlen.