Eigenschaften
- Art: Competition
- Finish: Black
- Modell: XD
- Waffentyp: Springfield
- Versandgewicht: 0.05kg
- Versandhöhe: 15mm
- Versandbreite: 109mm
- Versandlänge: 191mm
- UPC: 686461783067
Artikeldetails
US-Exportklassifizierung: 0A501.c

Das XD ULTIMATE MATCH TARGET TRIGGER KIT von POWDER RIVER PRECISION INC bietet dir eine herausragende Verbesserung für deine XD Pistole. Dieses Kit enthält alles, was du brauchst, um den Abzug deiner Waffe zu optimieren.
Das Kit umfasst den berühmten Striker Safety Lever von Powder River Precision, der den langen Vorweg des XD-Abzugs entfernt. Ausserdem sind reduzierte Abzugs- und Sear-Federn enthalten, um das Abzugsgewicht zu verringern. Der neue Sear hat einen patentierten Winkel, der hilft, den Abzug zu erleichtern und einen klaren, präzisen Bruch zu ermöglichen.
Der Abzug besteht aus robustem, leichtem Polymer, das den Reset beschleunigt. Zudem verfügt er über einen integrierten Übertravel-Stopp auf der Rückseite des Abzugs. Diese Methode des Übertravel-Stopps reduziert zusätzlichen Stress auf den Abzugsstangen. Wenn das Kit korrekt installiert wird, erhältst du einen kurzen, präzisen Abzug (ca. 3,5-4lbs) mit einem schnellen Reset und halbiert die Gesamtlänge des Abzugs.
Das Kit erfordert eine geringe Anpassung und enthält Installationsanweisungen für Büchsenmacher. Es passt auf alle XD-Modelle (ausser dem XD 45 mit Daumensicherung oder neuen XD-Modellen). Dieser Abzug ist ein OEM-Teil von Springfield Armory, das in der Produktion von XD- und XDM-Pistolen erhältlich ist.
Well worth it 18.04.2017
I'm no gunsmith but this is easy enough to install. Takes some patience to fit the pieces properly without taking off too much but it is well worth the time. The trigger pull is noticeably much lighter, the break is much more crisp, and pre travel and over travel are minimized greatly. I was going to adjust my rear sight because I tend to shoot left with all handguns but with this trigger I'm back in the bullseye with much tighter groups. Go slow with the fitting, I had to remove almost the entire raised ridge on the side of the sear, a very small amount from the back of the sear so the grip safety wouldn't stick, and some on the back of the trigger over travel stop.
Powder River Ultimare Match Trigger 22.01.2016
Just finished installing this trigger in an older Springfield XD 45. Trigger pull was reduced 48% from factory pull of 7 pounds. Pre-travel was also reduced by roughly 50%. These specs were exactly as advertised by Powder River. The sear, striker safety lever and integral over-travel on the back of the replacement trigger all had to be fit by hand. The trickiest part of the job is fitting the striker safety lever to the pistol. If the safety lever does not depress far enough to clear the striker safety mounted in the slide, you're going to have one hell of a time getting the slide back off the frame of the pistol. Pay attention to the amount of downward travel in the original striker safety lever in relation to the back slide rail. In my pistol the original safety lever was pretty close to flush with the top of the frame rail. I duplicated the same approximate distance of downward travel on the replacement part. I recommend a good oil stone for use on the side of the sear and small reset tab on the inside of the safety lever. A file works just fine for filing the over-travel stop on the back side of the replacement trigger. Read the manufacturer's instructions carefully. Patience is a virtue on this job. You can always take a little more material off. It's gonna be hell getting any material to go back on.
Beim Laden dieses Inhalts ist ein Fehler aufgetreten. Bitte aktualisiere die Seite, um fortzufahren. Wenn das Problem weiterhin besteht, wende dich bitte an unseren Kundenservice.