Mon compte (Connexion)
Votre panier est vide.
0
Panier
Brownells Suisse - Le plus grand fournisseur d'Accessoires pour le tir, Pièces détachées & Outils d'Armurier Suisse / Schweiz
Langues: Deutsch Français Italiano
Home Pièces Carabine Pièces Receiver Pièces Clapets de Fenêtre d'Ejection Clapets Trappe d'Ejection WILSON COMBAT AR-15 EJECTION PORT COVER PARTS KIT ONLY

WILSON COMBAT
AR-15 EJECTION PORT COVER PARTS KIT ONLY

Soyez le premier à évaluer ce produit
810025500283 965900019
Quality replacement dust cover rod, c-clip and torsion spring for AR style rifles.   Changing them is very easy, but care must be taken to not lose the c-clips and to reassemble it correctly. Please read and follow the instructions below to get your new cover installed and ready to go: Push the hinge pin forward until you can see the little "c" clip, positioning it so the open end is toward you. Using small punches or a screw driver, very carefully push on each end of the clip until it pops off. It doesn't take much, so take it slow and easy. Force should not be required; the clip will be under the pin and easily removed. You can use tweezers, or a magnetic pickup, or carefully tilt the receiver until the clip comes out in your hand. Be careful it is small and is easily lost. Make note of the cover spring position. If you don't have a diagram, take a picture so you can put it back right later. Slide the hinge pin rearward, covering the spring with your hand so it is not lost when the tension is released. Keep working the rod rearward until it is clear. Go slow so you don't scratch your upper receiver. Installation is mostly reversing the above. An easy way to install the hinge pin spring is to position it with the short leg to the rear of the receiver, pointing up toward the ejection port. Push the hinge pin into the spring a bit. Grab the front part of the spring, lifting it away from the receiver and press the long leg down, allowing it to rest against the ejection port cover. Slide your hinge pin in the rest of the way. Line up the little slot on the hinge pin with the front wall of the hinge pin channel. Use the wall to slide the clip down against the pin and use a punch to push it into place. You'll hear an audible click as it engages properly.
Plus...
11.9 11.9 1 CHF
Référence: 965900019
WILSON COMBAT AR-15 EJECTION PORT COVER PARTS KIT ONLY
Ref Fabricant: TREPDK 810025500283
11.9 CHF 141 CHF 11.90 *
Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.
Caractéristiques: Manufacture: AR-15
Poser un question

Caractéristiques

Manufacture: AR-15 Poids du colis: 0.033kg Hauteur d'expédition: 19mm Largeur d'expédition: 102mm Longueur d'expédition: 203mm

Détails de l'article

Fabriqué au USA
US export classification: 0A501.x



Quality replacement dust cover rod, c-clip and torsion spring for AR style rifles.   Changing them is very easy, but care must be taken to not lose the c-clips and to reassemble it correctly. Please read and follow the instructions below to get your new cover installed and ready to go: Push the hinge pin forward until you can see the little "c" clip, positioning it so the open end is toward you. Using small punches or a screw driver, very carefully push on each end of the clip until it pops off. It doesn't take much, so take it slow and easy. Force should not be required; the clip will be under the pin and easily removed. You can use tweezers, or a magnetic pickup, or carefully tilt the receiver until the clip comes out in your hand. Be careful it is small and is easily lost. Make note of the cover spring position. If you don't have a diagram, take a picture so you can put it back right later. Slide the hinge pin rearward, covering the spring with your hand so it is not lost when the tension is released. Keep working the rod rearward until it is clear. Go slow so you don't scratch your upper receiver. Installation is mostly reversing the above. An easy way to install the hinge pin spring is to position it with the short leg to the rear of the receiver, pointing up toward the ejection port. Push the hinge pin into the spring a bit. Grab the front part of the spring, lifting it away from the receiver and press the long leg down, allowing it to rest against the ejection port cover. Slide your hinge pin in the rest of the way. Line up the little slot on the hinge pin with the front wall of the hinge pin channel. Use the wall to slide the clip down against the pin and use a punch to push it into place. You'll hear an audible click as it engages properly.
Plus...
SOCIAL MEDIA
BROWNELLS.CH
CATÉGORIES
COMMANDER
SERVICE CLIENTÈLE
Bienvenue!
Bienvenue sur brownells.ch, le plus grand fournisseur d'accessoires pour armes à feu, Pièces détachées et Outils armurier en Suisse!
 
Notre garantie - Votre satisfaction
Si vous aimez tirer, travailler sur les armes en tant que professionnel ou pour votre loisir, ou bien simplement posséder une arme à feu, brownells.fr est fait pour vous! Depuis plus de 75 ans, tireurs, armuriers professionnels, amateurs, militaires / armuriers des forces de l'ordre ou encore as du bricolage d'armes à feu se sont tournés vers brownells.ch pour s'approvisionner en pièces et fournitures de haute qualité dont ils ont besoin.
 
Vous trouverez plus de 50.000 produits, y compris des pièces détachées uniques d'armes à feu, des accessoires, des outils d'armuriers, des munitions et bien d'autres produits pour entretenir, réparer et mettre à niveau vos armes.professionnels, amateurs, militaires / armuriers des forces de l'ordre ou encore as du bricolage d'armes à feu se sont tournés vers brownells.ch pour s'approvisionner en pièces et fournitures de haute qualité dont ils ont besoin. 
Cloudflare
DIBS - Payments made easy
 
Brownells UK - World's Largest Supplier of Gun Parts, Gunsmith Tools & Shooting Accessories Brownells Norge - Komplett utvalg av ladeutstyr, våpendeler, kuler, hylser, kikkerter, optikk og luftvåpen Brownells Österreich - Einer der größten Lieferanten für Waffenteile, Büchsenmacherzubehör & Schießsportzubehör Brownells Deutschland - Einer der größten Lieferanten für Waffenteile, Büchsenmacherzubehör & Schießsportzubehör Brownells France - Le plus grand fournisseur d'Accessoires pour le tir, Pièces détachées & Outils d'Armurier Brownells Iberica - El mayor proveedor de accesorios para el Tiro, Piezas y herramientas del armero. Brownells Sverige - Världens största leverantör av Vapendelar, Vapensmide Verktyg & Skyttetillbehör Brownells Suomi Brownells Italia - Il negozio del più grande rivenditore di componenti e accessori per armi da tiro, difesa e caccia Brownells Polska - Największy na świecie dostawca części broni, narzędzi rusznikarskich & akcesoriów strzeleckich Brownells Česko - Největší světový dodavatel součástí zbraní, střeleckého příslušenství a zbrojního nářadí
* Le prix inclut la TVA mais pas la livraison .

© 2024 Brownells Suisse
Part of the Brownells Europe Group

Vue classique Vue mobile
Newsletter