Caractéristiques
- Type d'arme:
AR-15
- Poids du colis: 0.045kg
- Hauteur d'expédition: 1mm
- Largeur d'expédition: 79mm
- Longueur d'expédition: 152mm
- UPC: 813318020192
Détails de l'article
US export classification: 0A501.x
AR-15
Le prix inclut la TVA mais pas la livraison .
Référence: 100004898
N° fabr.: EBRV1
813318020192 Le levier de libération prolongé accélère les changements de chargeur et améliore la capacité du tireur à dégager rapidement et en toute sécurité les bourrages, les doubles alimentations et les pannes. Il te permet de saisir et de libérer le bolt avec le doigt de la gâchette à l'intérieur du pontet, au lieu d'utiliser ta main libre. Pousse vers le haut sur le levier pour verrouiller le bolt à l'arrière ; pousse légèrement vers le bas pour le libérer. Les deux opérations peuvent être effectuées sans retirer ta main de la poignée de pistolet. L'EBRv1 se fixe à la libération de bolt existante de ton fusil. Peut être installé ou retiré en quelques minutes sans altération permanente de ton fusil.Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.
Le prix inclut la TVA mais pas la livraison .
Le EBRV1 Extended Bolt Release de PHASE 5 TACTICAL est un levier de libération prolongé qui accélère les changements de chargeur et améliore ta capacité à dégager les pannes, les doubles alimentations et les dysfonctionnements rapidement et en toute sécurité.
AR-15
Not impressed, rather have the BAD lever 31.01.2017
Not impressed with it. I installed it and fit was not quite right. I feel the Magpul was better and easier to install. I wanted to give it a chance and its not for me. Will get Magpul for the next one.
AR-15 Ambi Fitment 20.10.2014
Purchased this to try on several AR-15 lowers. Sig 516, Sig M400 (it uses the same lower at the 516), a Windham lower and, a Rock River Lower. It works on all of them. Drops in easily. But, use caution when you are trying to use a small punch to remove the roll pin. Put a cloth or something round the entire area or you'll get to bare metal at the speed of light! Suggest save your pin. The one that normally comes with this EBRv1 may or, may not be in the package......And, slowly does it and, it'll drop right in. Also, use caution you don't lose the pin and spring under the latch......it can fly out or fall out and, they are small......hard to find etc. It is well designed in my opinion, solid and does it's job. but, I docked it a star because for my taste.....I would like the part that goes thru the trigger housing area, to be about 1/8" longer and, it should be bent down a few degree's to keep it down slightly lower for ease of operation. I also have a nice slip over one I bought from Tactical Link on the M400, I found that I had to bend that Tac Link one slightly out away from the lower, in order to keep it from contacting the lower where it goes thru the trigger housing......Before I did that, I was having trouble with the system failing to lock back the bolt after the mag was empty. Which is a pain because you're never sure if you had a FTF or, not. The Sig's (M400/516) need a straight down handle so it doesn't hit the left side mag release. The ambi bolt release I like the best, I bought from Troy industries.......the handles slight longer and, on the Windham and RRA's lowers it doesn't touch anything. If anyone would like to know the number of that my email is below, or they are easily found at both sites......Hope this helps.......
Nous avons rencontré une erreur lors du chargement de ce contenu. Veuillez actualiser la page pour continuer. Si le problème persiste, contactez notre service client.