Adds Extra Elevation For Sights & Other Accessories
Add-on riser rail gives an additional ½" of elevation or offset sometimes needed to mount a red dot sight, light, laser, or other essential accessory. Clamps securely to any MIL-STD 1913 Picatinny rail and provides three Picatinny cross-slots. Steel crossbolt and oversized, hex-head slotted thumbscrew enable fast, easy installation and removal, with or without tools.
Ajoute une élévation supplémentaire pour sites & d'autres accessoires
Rail de montage le module donne une supplémentaire ½" d'élévation ou de décalage parfois nécessaire de monter un viseur point rouge, lumière, laser ou autre accessoire indispensable. Se fixe solidement à n'importe quel rail Picatinny MIL-STD 1913 et fournit trois rainures en croix Picatinny. Boulon en acier et vis à oreilles surdimensionnées, tête hexagonale fendue activez rapide, facilité d'installation et de retrait, avec ou sans outils.
FICHE
: Rail – 6061 T6 aluminium, revêtement dur anodisé, noir. Boulon/vis de serrage – 4140 oxyde noir, acier finition. 13 ⁄ 8"(3,5 cm) de long, 1½ po (3,8 cm) de large. Offre supplémentaire élévation de ½ po (12,7 mm). poids 1,4 oz (38g).
Plus...
Évaluations client de BROWNELLS 1/2" MINI RISER MOUNT
Nombre d'évaluations: 4
De brownells.com: 4
Note moyenne: 4.5
44 CARBINE BASE MOUNT(09.02.2011)
I BOUGHT A ONE INCH HIGH MICRO MOUNT FOR THE 44 CARBINE THAT I HAVE. ITS JUST TOO HIGH. I MEASURED THIS HALF INCH HIGH RISER AND IT WAS PERFECT.
Superb Quality!(06.08.2011)
Used this to mount a Sig STS-081 red dot sight to my S&W 15/22 rifle. Worked perfect! 1/2" height of the mount, lined it right up with the sights, which are now the back-up sights. Thanks Brownells!
Buy Brownells not Yankee Hill(20.02.2012)
Bought the Yankee Hill and it wobbles on my AR rail. Tried it on every other rail I have and it wobbled on all of them. Bought Brownells and it clamps on tighter than a fishes butt. The bolt is large and sticks out a bit more than I would prefer and it is heavy, but obviously well constructed. The Yankee Hill has good reviews about synching down tightly...I have no idea why. If you want to use the Yankee Hill you have to unscrew both screws with an allen wrench almost all of the way out. It is way too painful to do all that for it to rattle when you move your rifle. The Brownells is much easier. Just the single screw to tighten by hand then with a screwdriver for a few turns. Easy, simple and stable. Do yourself a favor, buy Brownells.
Shoots loose(27.02.2016)
450 bushmaster shook it loose don't want to use tread locker as defeats purpose added a lock washer problem solved.
Also Leupold QRW and PRW seats up on the cross block not the ring base.
And if your top set is also a bolt down or lever you have to reverse one of the sets do to clearance issues of the lock nut
Référence: 080000713 BROWNELLS 1/2" MINI RISER MOUNT050806109858 Rail de montage le module donne une supplémentaire ½" d'élévation ou de décalage parfois nécessaire de monter un viseur point rouge, lumière, laser ou autre accessoire indispensable. Se fixe solidement à n'importe quel rail Picatinny MIL-STD 1913 et fournit trois rainures en croix Picatinny. Boulon en acier et vis à oreilles surdimensionnées, tête hexagonale fendue activez rapide, facilité d'installation et de retrait, avec ou sans outils.
29.9CHF3CHF 29.90
*
Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.
Adds Extra Elevation For Sights & Other Accessories
Add-on riser rail gives an additional ½" of elevation or offset sometimes needed to mount a red dot sight, light, laser, or other essential accessory. Clamps securely to any MIL-STD 1913 Picatinny rail and provides three Picatinny cross-slots. Steel crossbolt and oversized, hex-head slotted thumbscrew enable fast, easy installation and removal, with or without tools.
Ajoute une élévation supplémentaire pour sites & d'autres accessoires
Rail de montage le module donne une supplémentaire ½" d'élévation ou de décalage parfois nécessaire de monter un viseur point rouge, lumière, laser ou autre accessoire indispensable. Se fixe solidement à n'importe quel rail Picatinny MIL-STD 1913 et fournit trois rainures en croix Picatinny. Boulon en acier et vis à oreilles surdimensionnées, tête hexagonale fendue activez rapide, facilité d'installation et de retrait, avec ou sans outils.
FICHE
: Rail – 6061 T6 aluminium, revêtement dur anodisé, noir. Boulon/vis de serrage – 4140 oxyde noir, acier finition. 13 ⁄ 8"(3,5 cm) de long, 1½ po (3,8 cm) de large. Offre supplémentaire élévation de ½ po (12,7 mm). poids 1,4 oz (38g).
Plus...
Évaluations client de BROWNELLS 1/2" MINI RISER MOUNT
Nombre d'évaluations: 4
De brownells.com: 4
Note moyenne: 4.5
44 CARBINE BASE MOUNT(09.02.2011)
I BOUGHT A ONE INCH HIGH MICRO MOUNT FOR THE 44 CARBINE THAT I HAVE. ITS JUST TOO HIGH. I MEASURED THIS HALF INCH HIGH RISER AND IT WAS PERFECT.
Superb Quality!(06.08.2011)
Used this to mount a Sig STS-081 red dot sight to my S&W 15/22 rifle. Worked perfect! 1/2" height of the mount, lined it right up with the sights, which are now the back-up sights. Thanks Brownells!
Buy Brownells not Yankee Hill(20.02.2012)
Bought the Yankee Hill and it wobbles on my AR rail. Tried it on every other rail I have and it wobbled on all of them. Bought Brownells and it clamps on tighter than a fishes butt. The bolt is large and sticks out a bit more than I would prefer and it is heavy, but obviously well constructed. The Yankee Hill has good reviews about synching down tightly...I have no idea why. If you want to use the Yankee Hill you have to unscrew both screws with an allen wrench almost all of the way out. It is way too painful to do all that for it to rattle when you move your rifle. The Brownells is much easier. Just the single screw to tighten by hand then with a screwdriver for a few turns. Easy, simple and stable. Do yourself a favor, buy Brownells.
Shoots loose(27.02.2016)
450 bushmaster shook it loose don't want to use tread locker as defeats purpose added a lock washer problem solved.
Also Leupold QRW and PRW seats up on the cross block not the ring base.
And if your top set is also a bolt down or lever you have to reverse one of the sets do to clearance issues of the lock nut