This mount is NOT a drop in part and will require fitting. EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. EGW products should be installed and checked by a qualified and competent gunsmith. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail after checking for fit Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits: Firearms with oversized Novak cut dovetails. This mount is made .007"" larger than a standard Novak cut and will require fitting.
Montaggio di precisione per il tuo Vortex Viper/Venom
Il montaggio OVERSIZED NOVAK 0.007" VORTEX VIPER/VENOM è progettato per una perfetta integrazione con le tue ottiche. Questo supporto non è un componente di semplice installazione e richiede una messa a punto accurata.
Descrizione del prodotto
Il montaggio EGW è progettato per essere installato da sinistra a destra (con la bocca rivolta in avanti). La guida ha un taper progressivo per facilitare l'installazione. Segui questi passaggi per montare il tuo Vortex Viper/Venom, Burris FastFire o Docter red-dot sight:
- Rimuovi il mirino posteriore dalla tua arma.
- Installa il montaggio EGW nella guida dopo aver controllato la compatibilità.
- Serra la vite di bloccaggio (se applicabile).
- Posiziona il red dot sight sul montaggio EGW (mettere un piccolo pezzo di carta tra il red dot e il montaggio faciliterà la rimozione e proteggerà il red dot dall'adesivo Loctite).
- Applica Loctite blu alle viti di montaggio fornite.
- Serra le viti di montaggio a 15in/lbs.
Incluso nel pacchetto
- 2 viti a testa bombata - Fornite per i mirini Vortex Viper e Venom.
- 2 viti a testa piatta - Fornite per i mirini Burris FastFire e Docter.
Le viti incluse in questo montaggio richiedono una chiave a brugola da 5/64'' per l'installazione. La modifica della tua arma potrebbe annullare la garanzia del produttore.
Questo prodotto deve essere installato e controllato da un armaiolo qualificato. Non si assume alcuna responsabilità per danni o infortuni che possono derivare da un'installazione o uso improprio di questo prodotto.
Compatibilità
Questo montaggio è compatibile con armi dotate di guide a taglio Novak oversized. È realizzato con uno spessore di .007" maggiore rispetto a un taglio Novak standard e richiederà una messa a punto.