Il Carrello è vuoto.

Carrello

0917309915

Suisse / Schweiz

Lingue: Deutsch Français Italiano

VOLQUARTSEN
REMINGTON 597 TARGET HAMMER

810162011321 930000019

Reduces Pull Weight To Improve Accuracy

Fully machined from A2 tool steel with the hammer notch individually, surface ground to ensure an exact angle of engagement. Reduces felt trigger pull by up to 50 percent. Drop-in installation; use in an unaltered, factory triggerguard. Fits both the .22LR and .22WMR.

SPECS: A2 tool steel, in the white. Hardened to Rc 58.

Altro...

Riduce il peso di Pull per migliorare l'accuratezza

Completamente lavorata da acciaio A2 con la tacca di martello individualmente, superficie di terra per assicurare un angolo esatto di fidanzamento. Riduce il tiro di innesco di feltro fino al 50 per cento. Installazione di drop-in; utilizzare un inalterato, guardamano di fabbrica. Si inserisce il 22Lr e il .22WMR.

Specifiche: A2 strumento d'acciaio, in bianco. Induriti per Rc 58.

Altro...

Punteggi dei clienti per VOLQUARTSEN TARGET HAMMER

Numero di punteggi: 8
Da brownells.com: 8
Punteggio medio: 5

Worth the Effort (22.07.2010)

Just finished installing the hammer. Initial trigger pull approx. 4 1/2 lbs. according to spring gauge. After installation: 2 lbs. Minimal creep. Took about 15-20 minutes. Remove trigger housing from receiver by removing the one retaining pin at rear of trigger housing(if bolt is closed, may have to pull back slightly to get housing to pop free). Place housing in padded vice at a slight angle to avoid crushing mag release button. Housing is composite so easy does it. Tap out hammer pin with punch but just enough to release hammer-don't drive out all the way. Don't remove punch but leave in pin hole to keep spring and plastic bushing in place(there are two plastic bushings inside of spring on both sides of hammer). Remove old hammer and slide in new one, align pin holes and reinstall hammer pin. You may find that you cannot get the hammer to go to the cocked position. If this is so, you have to push the trigger fully forward and the hammer should stay in the cocked position now. Install housing back into receiver and replace the one retaining pin. Install upper assembly back into stock and your done. With gun empty, check to make sure rifle fires after bolt is cycled. Mine functioned flawlessly. If you completed the job without ending up with a bunch of extra parts, you should be very pleased with the results.

Money well spent!! (03.06.2011)

If you buy one part for your 597, make it this! Very easy installation and a dramatic difference in trigger pull. I still just can't believe how smooth and nice it is. Just buy it!!

BUY IT (25.12.2011)

Easy to install.
Reduces triger pull.
Smoother trigger.
Buy it. You will love it.

Great Prodct!! (17.01.2012)

Slid this puppy right into my HB 597 after getting really good on-line videos do demonstrate (at Rimfirecentral.com) or elsewhere. It does exactly as claimed, makes trigger light and crisp.

Need to have in your Remington 597 (13.11.2013)

I'm very pleased about this product, really surpised about how it works overrided my spectatives, my Rem597 is in a new level of trigger and shooting control. Very fast shipping and a real proffesional package. My first but not my last buy with brownells. Thanks a lot.

Effective Solution (02.12.2013)

This was the perfect solution for the VERY heavy trigger on my daughter's 597. Easy to install; but be patient with the pin for the hammer.

Now the pull is crisp and light, with no creep. Trigger pull was reduced by more than 50%

This product was very cost effective compared to some of the other solutions out there.

High Quality Product!

great product (02.09.2014)

This hammer combined with a Brownell's extractor made an otherwise misfiring and jamming gun shoot flawlessly. I was able to shoot four different types of ammo totaling about 400 rounds without any FTE or FTF. This gun out of the box did not function properly. Now it shoots great and is extremely accurate. A must upgrade for any Remington 597 owner!

YouTube Video helps (13.05.2016)

My 597 has a great barrel, but a lousy trigger. Getting the most out of your gun comes right down to the trigger. Why do you think benchrest shooters use 4 - 6 Oz. triggers. So I ordered this item with my fingers crossed. Got it promptly and installed it in 45 minutes. Use Youtube video (9min ) and it is very straight forward. End result Trigger pull 3 1/4 - 3 1/2 Lbs.

Now to get to the range.

Leggi più recensioni su brownells.com

74.9 74.9 1 CHF

N. prodotto: 930000019
VOLQUARTSEN TARGET HAMMER
Parti Fabbricante: VCRTH 810162011321 Completamente lavorata da acciaio A2 con la tacca di martello individualmente, superficie di terra per assicurare un angolo esatto di fidanzamento. Riduce il tiro di innesco di feltro fino al 50 per cento. Installazione di drop-in; utilizzare un inalterato, guardamano di fabbrica. Si inserisce il 22Lr e il .22WMR.

74.9 CHF 4 CHF 74.90 *

Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.

Caratteristiche: Adatto per: Remington Modello: 597

Aggiungi alla lista degli acquisti

Domande

Dettagli

Aggiungi alla lista degli acquisti

Domande

Caratteristiche

Adatto per: Remington Modello: 597 Peso della spedizione: 0.014kg Altezza di spedizione: 8mm Larghezza di spedizione: 71mm Lunghezza di spedizione: 86mm

Dettagli dell'elemento

Made in Usa
Classificazione per l'export dagli US: 0A501.c

Reduces Pull Weight To Improve Accuracy

SPECS: A2 tool steel, in the white. Hardened to Rc 58.

Altro...

Riduce il peso di Pull per migliorare l'accuratezza

Specifiche: A2 strumento d'acciaio, in bianco. Induriti per Rc 58.

Altro...

Punteggi dei clienti per VOLQUARTSEN TARGET HAMMER

Numero di punteggi: 8
Da brownells.com: 8
Punteggio medio: 5

Worth the Effort (22.07.2010)

Money well spent!! (03.06.2011)

If you buy one part for your 597, make it this! Very easy installation and a dramatic difference in trigger pull. I still just can't believe how smooth and nice it is. Just buy it!!

BUY IT (25.12.2011)

Easy to install.
Reduces triger pull.
Smoother trigger.
Buy it. You will love it.

Great Prodct!! (17.01.2012)

Slid this puppy right into my HB 597 after getting really good on-line videos do demonstrate (at Rimfirecentral.com) or elsewhere. It does exactly as claimed, makes trigger light and crisp.

Need to have in your Remington 597 (13.11.2013)

Effective Solution (02.12.2013)

great product (02.09.2014)

YouTube Video helps (13.05.2016)

Leggi più recensioni su brownells.com

Scelti da altri clientie

CHECK-MATE INDUSTRIES SPRINGFIELD M1A/M14 MAGAZINE 308 WINCHESTER 15RD STEEL BLACK
SPRINGFIELD M1A 10RD MAGAZINE 308 WINCHESTER

CHECK-MATE INDUSTRIES

Riordinato

CHF 49.90 * CHF 39.90 - CHF 209.90*

Caricatori | Magazines

4.7

Accesso

Hai dimenticato la password?
Registrati

SOCIAL MEDIA

Facebook

BROWNELLS.CH

CATALOGO PRODOTTI

ORDINARE

CUSTOMER SERVICE

Benvenuti!

Benvenuti su Brownells.ch, il principale rivenditore online di accessori per armi da fuoco, componenti di pistole e utensili per armaioli in Svizzera!

La nostra offerta

Se ti piace sparare, lavorare sulle armi da fuoco come artigiano o per hobby, o semplicemente possiedi un'arma, questo è il posto per te! Grazie alla nostra grande esperienza, ogni giorno, tiratori, armaioli professionisti, hobbisti, militari, esponenti delle forze dell'ordine e appassionati d'armi si rivolgono a Brownells.ch per trovare accessori e componenti di alta qualità e fare rifornimento di ciò di cui hanno bisogno.