Trims The Rivet Tip To Make Broken Ejector Spring Removal Simple
Hollow-end mill fits in drill press, spot faces the front rivet to take off just the peened area. Often lets you re-peen the existing rivet and eliminate rebluing the receiver.
Taglia la punta del ribattino per rendere semplice rimozione Molla espulsore rotto
Hollow-fresa adatta nel trapano, spot affronta il ribattino anteriore a decollare solo la zona martellata. Spesso consente di ri-peen rivetto esistente ed eliminare rebluing il ricevitore.
Punteggi dei clienti per BROWNELLS REMINGTON 870 EJECTOR SPRING RIVET CUTTER
Numero di punteggi: 1
Da brownells.com: 1
Punteggio medio: 5
Great investment!(10.02.2016)
This little rivet cutter made me save over $200 in gunsmithing work on my old 870 Wingmaster, which had been sitting in the gun safe for years because of a ''too-expensive-to-replace'' broken ejector spring. The instructions provided with the tool are very clear and allowed me, as indicated, to re-use the rivet to lock the new spring into the ejector. The only thing I did differently than prescribed by the instructions was to drive the rivet cutter down on the tiny rivet head by hand instead of using a press drill. The rivet cutter being very sharp and the rivet metal being very soft, I was afraid to ruin the rivet using a press drill. It took me 10 minutes to cut the rivet head slowly and safely by hand (clockwise twist of the fingers with little pressure).
N. prodotto: 080000040 BROWNELLS REMINGTON 870 EJECTOR SPRING RIVET CUTTER050806103825 Hollow-fresa adatta nel trapano, spot affronta il ribattino anteriore a decollare solo la zona martellata. Spesso consente di ri-peen rivetto esistente ed eliminare rebluing il ricevitore.
54.9CHF0CHF 54.90
*
In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.
Adatto per:
Remington
Materiale:
Acciaio
Modello:
870
Peso della spedizione: 0.029kgAltezza di spedizione: 8mmLarghezza di spedizione: 91mmLunghezza di spedizione: 170mm
Trims The Rivet Tip To Make Broken Ejector Spring Removal Simple
Hollow-end mill fits in drill press, spot faces the front rivet to take off just the peened area. Often lets you re-peen the existing rivet and eliminate rebluing the receiver.
Taglia la punta del ribattino per rendere semplice rimozione Molla espulsore rotto
Hollow-fresa adatta nel trapano, spot affronta il ribattino anteriore a decollare solo la zona martellata. Spesso consente di ri-peen rivetto esistente ed eliminare rebluing il ricevitore.
Punteggi dei clienti per BROWNELLS REMINGTON 870 EJECTOR SPRING RIVET CUTTER
Numero di punteggi: 1
Da brownells.com: 1
Punteggio medio: 5
Great investment!(10.02.2016)
This little rivet cutter made me save over $200 in gunsmithing work on my old 870 Wingmaster, which had been sitting in the gun safe for years because of a ''too-expensive-to-replace'' broken ejector spring. The instructions provided with the tool are very clear and allowed me, as indicated, to re-use the rivet to lock the new spring into the ejector. The only thing I did differently than prescribed by the instructions was to drive the rivet cutter down on the tiny rivet head by hand instead of using a press drill. The rivet cutter being very sharp and the rivet metal being very soft, I was afraid to ruin the rivet using a press drill. It took me 10 minutes to cut the rivet head slowly and safely by hand (clockwise twist of the fingers with little pressure).