Precisely aligns individual steel stamps to help ensure characters are straight and evenly spaced when stamping caliber designations on barrels. Allen head screws allow adjustment for accurate character spacing, so you get truly professional looking results. Machined port allows an unobstructed view of the first stamp head to ensure correct positioning on workpiece prior to tapping with your hammer. Accepts ¼" square stamps with 1/16", 3/32", or 1/8" character sizes. Fits barrels up to 1-3/8" diameter.
SPECS: Aluminum, natural finish with steel U-bolt and hardware. 2-3⁄8" (6cm) long x 3¼ (8.2cm) wide, 1½ (3.8cm) high.
Altro...
Per l'allineamento di precisione quando marcatura botti
Allinea precisamente singoli francobolli in acciaio per aiutare a garantire caratteri sono dritti e uniformemente spaziati quando denominazioni di calibro su barili di stampaggio. Viti esagonali permettono la regolazione per spaziatura carattere preciso, così si ottiene veramente professionale alla ricerca di risultati. Porta lavorata permette una vista non ostruita del capo primo francobollo per assicurare il corretto posizionamento sul pezzo in lavorazione prima della spillatura con il martello. Accetta ¼" bolli quadrati con dimensioni di carattere 1/16", 3/32" o 1/8". Si inserisce botti fino a 1-3/8" di diametro.
Specifiche: alluminio, finitura naturale con acciaio cavallotto e hardware. 2-3 ⁄ 8 cm (6) lungo x 3¼ (8,2 cm) ampia, 1½ (3,8 cm) alto.
Altro...
Punteggi dei clienti per LA BOUNTY STEEL STAMP GUIDE
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 1
Caution(08.01.2010)
The device is well made, however it will slip resulting in uneven markings. After reading the instructions over several times I tried it. I was disappointed with the results. I then tried it again on an old barrel and the same thing happened again. I made sure the holding ring was very tight. My opinion is save your maoney and go to a jeweler of plaque company that can do it right, the first time.
warning - disapointed(06.12.2012)
I was not able to get this device to work well even when following the directions. In the end, I was able to load several stamps in a row then tighten up the guide and clamp the assembly to a barrel. Even this way, it was hard to use. The clearance between the plates was too tight to insert the stamps without loosening the side screws. It is hard to get just five stamps into the guide (e.g., 300H&H cannot be done without the alignment risk of a second setup). I wish I had read keydiverfla's review before laying down my money.
N. prodotto: 521104000 LA BOUNTY STEEL STAMP GUIDE Parti Fabbricante: NONE Allinea precisamente singoli francobolli in acciaio per aiutare a garantire caratteri sono dritti e uniformemente spaziati quando denominazioni di calibro su barili di stampaggio. Viti esagonali permettono la regolazione per spaziatura carattere preciso, così si ottiene veramente professionale alla ricerca di risultati. Porta lavorata permette una vista non ostruita del capo primo francobollo per assicurare il corretto posizionamento sul pezzo in lavorazione prima della spillatura con il martello. Accetta ¼" bolli quadrati con dimensioni di carattere 1/16", 3/32" o 1/8". Si inserisce botti fino a 1-3/8" di diametro.
69.9CHF5CHF 69.90
*
Tempi di consegna circa 8-15 giorni dal magazzino negli Stati Uniti.
Precisely aligns individual steel stamps to help ensure characters are straight and evenly spaced when stamping caliber designations on barrels. Allen head screws allow adjustment for accurate character spacing, so you get truly professional looking results. Machined port allows an unobstructed view of the first stamp head to ensure correct positioning on workpiece prior to tapping with your hammer. Accepts ¼" square stamps with 1/16", 3/32", or 1/8" character sizes. Fits barrels up to 1-3/8" diameter.
SPECS: Aluminum, natural finish with steel U-bolt and hardware. 2-3⁄8" (6cm) long x 3¼ (8.2cm) wide, 1½ (3.8cm) high.
Altro...
Per l'allineamento di precisione quando marcatura botti
Allinea precisamente singoli francobolli in acciaio per aiutare a garantire caratteri sono dritti e uniformemente spaziati quando denominazioni di calibro su barili di stampaggio. Viti esagonali permettono la regolazione per spaziatura carattere preciso, così si ottiene veramente professionale alla ricerca di risultati. Porta lavorata permette una vista non ostruita del capo primo francobollo per assicurare il corretto posizionamento sul pezzo in lavorazione prima della spillatura con il martello. Accetta ¼" bolli quadrati con dimensioni di carattere 1/16", 3/32" o 1/8". Si inserisce botti fino a 1-3/8" di diametro.
Specifiche: alluminio, finitura naturale con acciaio cavallotto e hardware. 2-3 ⁄ 8 cm (6) lungo x 3¼ (8,2 cm) ampia, 1½ (3,8 cm) alto.
Altro...
Punteggi dei clienti per LA BOUNTY STEEL STAMP GUIDE
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 1
Caution(08.01.2010)
The device is well made, however it will slip resulting in uneven markings. After reading the instructions over several times I tried it. I was disappointed with the results. I then tried it again on an old barrel and the same thing happened again. I made sure the holding ring was very tight. My opinion is save your maoney and go to a jeweler of plaque company that can do it right, the first time.
warning - disapointed(06.12.2012)
I was not able to get this device to work well even when following the directions. In the end, I was able to load several stamps in a row then tighten up the guide and clamp the assembly to a barrel. Even this way, it was hard to use. The clearance between the plates was too tight to insert the stamps without loosening the side screws. It is hard to get just five stamps into the guide (e.g., 300H&H cannot be done without the alignment risk of a second setup). I wish I had read keydiverfla's review before laying down my money.