Brownells Suisse - Le plus grand fournisseur d'Accessoires pour le tir, Pièces détachées & Outils d'Armurier Suisse / Schweiz

BROWNELLS
CROWN SAVER™ LATHE CENTER COVER

080000379
Your Safeguard When Turning Barrels With Finished Crowns
These brass cones take much of the anxiety out of lathe-turning a perfectly good barrel with an already finished crown. Insert a Crown Saver between the muzzle and lathe or mill center before fluting, chambering, polishing, or threading for a muzzle brake, and you can rest assured you won’t harm the rifling or ding the crown. Each brass cone is machined to within .0002" or less concentricity, making using a Crown Saver as accurate as direct barrel contact against the center. With a Crown Saver, you virtually eliminate any chance of swaging the rifling. It stays seated and will not spin in the bore when the barrel is chucked in the lathe. Small fits bores .17 to .45 caliber. Large fits bores up to .50 caliber. For best results, do not use Crown Saver more than once on barrels of the same caliber.

SPECS: 360 brass. Maximum diameter. Small - .500", Large - .750".

48.9 48.9 1 CHF
Référence: 080000379
BROWNELLS CROWN SAVER LATHE CENTER COVER SMALL 10 PACK
Ref Fabricant: 080000379 Ces cônes en laiton prennent une grande partie de l'anxiété de tour-tourner un baril parfaitement bien avec une couronne déjà fini. Insérer un état de veille entre le museau et tour ou Moulin centre avant cannelage, chambering, polissage ou enfiler pour un frein de bouche, et vous pouvez être assuré, vous ne pas endommager les rayures ou ding de la Couronne. Chaque cône de laiton est usinée dans. 0002" ou moins concentricité, fabrication à l'aide d'une bouée de couronne aussi précis que le Canon direct contact contre le centre. Avec un état de veille, vous éliminez pratiquement toute chance de retreinte les rayures. Il reste assis et ne tourne pas dans l'alésage lorsque le Canon est jeté dans le tour. Petits ajustements alésages calibre.17 à.45. Gros ajustements alésages jusqu'à calibre.50. Pour de meilleurs résultats, n'utilisez pas Couronne Saver plus d'une fois sur les canons du même calibre.
48.9 CHF 0 CHF 48.90 *
En rupture de stock, délai de livraison d'environ 4-12 semaines depuis l'entrepôt des États-Unis.

Caractéristiques

Poids du colis: 0.045kg Largeur d'expédition: 83mm Longueur d'expédition: 146mm

Détails de l'article

Fabriqué au USA



Your Safeguard When Turning Barrels With Finished Crowns
These brass cones take much of the anxiety out of lathe-turning a perfectly good barrel with an already finished crown. Insert a Crown Saver between the muzzle and lathe or mill center before fluting, chambering, polishing, or threading for a muzzle brake, and you can rest assured you won’t harm the rifling or ding the crown. Each brass cone is machined to within .0002" or less concentricity, making using a Crown Saver as accurate as direct barrel contact against the center. With a Crown Saver, you virtually eliminate any chance of swaging the rifling. It stays seated and will not spin in the bore when the barrel is chucked in the lathe. Small fits bores .17 to .45 caliber. Large fits bores up to .50 caliber. For best results, do not use Crown Saver more than once on barrels of the same caliber.

SPECS: 360 brass. Maximum diameter. Small - .500", Large - .750".

Newsletter