Brownells Suisse - Le plus grand fournisseur d'Accessoires pour le tir, Pièces détachées & Outils d'Armurier Suisse / Schweiz

BROWNELLS
CERROSAFE® CHAMBER CASTING ALLOY

080027100
Never Wears Out- Use Over And Over
There are various products on the market which can be used to make a cast of a gun chamber. To be certain that the product we are offering you is the best and most practical, we contacted the basic manufacturer. They recommended Cerrosafe because of its unique features. Unlike Woodsmetal which swells upon cooling and cannot be removed from a gun chamber, Cerrosafe shrinks during the first 30 minutes of cooling and then at the end of an hour, is EXACTLY chamber size. At the end of 200 hours it will have expanded approximately .0025". This factor is well known by all toolmakers and they will take it into consideration when making dies or reamers or gauges from your cast - if you will tell them the cast is of Cerrosafe. Cerrosafe melts between 158° - 190° F. It should be melted in a clean, iron ladle. Source of heat should be removed as soon as the alloy is completely melted, at which time it is ready to pour. The solidified casting should be removed from the chamber before, or when, it cools to room temperature. If allowed to remain in the mold over an hour, it will grip the chamber walls and be difficult to remove. Clean the chamber of the rifle thoroughly, then plug the bore immediately ahead of the throat with a small rag - but not so tightly it cannot be driven out. If possible, pour the molten Cerrosafe through a small tube into the bottom of the cast, gradually removing the tube as the chamber fills. If the barrel is cold, warm it to room temperature or above before making the cast. When cooled, remove from chamber, using a rod or dowel from the muzzle end of the gun.
SPECS: Sold by weight. Alloy. Infinitely reusable.
26.9 46.9 2 CHF
Référence: 080027100
BROWNELLS CERROSAFE CHAMBER CASTING ALLOY 1LB Il existe différents produits sur le marché qui peut être utilisé pour effectuer un cast d'une chambre de l'arme à feu. Pour être certain que le produit que nous vous offrons est la meilleure et plus pratique, nous avons contacté le constructeur de base. Ils ont recommandé des Cerrosafe en raison de ses caractéristiques uniques. Contrairement à Woodsmetal qui se dilate lors du refroidissement et ne peuvent pas être retiré d'une chambre du Canon, Cerrosafe se rétrécit pendant les 30 premières minutes de refroidissement, puis au bout d'une heure, est exactement les dimensions de chambre. À la fin de 200 heures il sera ont élargi approximativement. 0025". Ce facteur est bien connu par tous les fabricants d'outils et ils seront prendre en considération lors de matrices ou alésoirs ou jauges d'après votre moulage - si vous leur direz que le casting est de Cerrosafe. Cerrosafe fait fondre entre 158° - 190° c. Il doit être fondu dans une louche de fer pur. Source de chaleur doit être retiré dès que l'alliage est complètement fondu, à laquelle il est prêt à verser. La coulée solidifiée doit être enlevée de la chambre avant, ou lorsqu'il se refroidit jusqu'à la température ambiante. Si autorisé à rester dans le moule, plus d'une heure, il va saisir les murs de la chambre et être difficiles à enlever. Nettoyer la chambre du fusil, puis branchez l'alésage immédiatement devant la gorge avec un petit chiffon - mais pas de façon aussi stricte il ne peut être chassée. Si possible, verser la fondue Cerrosafe à travers un petit tube dans le bas de la distribution, supprimant progressivement le tube dans la chambre se remplit. Si le Canon est froid, le réchauffer à température ambiante ou plus avant d'effectuer le cast. Lorsque refroidi, retirez de la chambre, à l'aide d'une tige ou un goujon de l'extrémité du museau du pistolet.
46.9 CHF 126 CHF 46.90 *
Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.

Caractéristiques

Poids du colis: 0.454kg Hauteur d'expédition: 8mm Largeur d'expédition: 76mm Longueur d'expédition: 226mm

Détails de l'article

Fabriqué au USA



Référence: 080027050
BROWNELLS CERROSAFE CHAMBER CASTING ALLOY 1/2LB Il existe différents produits sur le marché qui peut être utilisé pour effectuer un cast d'une chambre de l'arme à feu. Pour être certain que le produit que nous vous offrons est la meilleure et plus pratique, nous avons contacté le constructeur de base. Ils ont recommandé des Cerrosafe en raison de ses caractéristiques uniques. Contrairement à Woodsmetal qui se dilate lors du refroidissement et ne peuvent pas être retiré d'une chambre du Canon, Cerrosafe se rétrécit pendant les 30 premières minutes de refroidissement, puis au bout d'une heure, est exactement les dimensions de chambre. À la fin de 200 heures il sera ont élargi approximativement. 0025". Ce facteur est bien connu par tous les fabricants d'outils et ils seront prendre en considération lors de matrices ou alésoirs ou jauges d'après votre moulage - si vous leur direz que le casting est de Cerrosafe. Cerrosafe fait fondre entre 158° - 190° c. Il doit être fondu dans une louche de fer pur. Source de chaleur doit être retiré dès que l'alliage est complètement fondu, à laquelle il est prêt à verser. La coulée solidifiée doit être enlevée de la chambre avant, ou lorsqu'il se refroidit jusqu'à la température ambiante. Si autorisé à rester dans le moule, plus d'une heure, il va saisir les murs de la chambre et être difficiles à enlever. Nettoyer la chambre du fusil, puis branchez l'alésage immédiatement devant la gorge avec un petit chiffon - mais pas de façon aussi stricte il ne peut être chassée. Si possible, verser la fondue Cerrosafe à travers un petit tube dans le bas de la distribution, supprimant progressivement le tube dans la chambre se remplit. Si le Canon est froid, le réchauffer à température ambiante ou plus avant d'effectuer le cast. Lorsque refroidi, retirez de la chambre, à l'aide d'une tige ou un goujon de l'extrémité du museau du pistolet.
26.9 CHF 77 CHF 26.90 *
Délai de livraison environ 8-15 jours depuis l'entrepôt des États-Unis.
Never Wears Out- Use Over And Over
There are various products on the market which can be used to make a cast of a gun chamber. To be certain that the product we are offering you is the best and most practical, we contacted the basic manufacturer. They recommended Cerrosafe because of its unique features. Unlike Woodsmetal which swells upon cooling and cannot be removed from a gun chamber, Cerrosafe shrinks during the first 30 minutes of cooling and then at the end of an hour, is EXACTLY chamber size. At the end of 200 hours it will have expanded approximately .0025". This factor is well known by all toolmakers and they will take it into consideration when making dies or reamers or gauges from your cast - if you will tell them the cast is of Cerrosafe. Cerrosafe melts between 158° - 190° F. It should be melted in a clean, iron ladle. Source of heat should be removed as soon as the alloy is completely melted, at which time it is ready to pour. The solidified casting should be removed from the chamber before, or when, it cools to room temperature. If allowed to remain in the mold over an hour, it will grip the chamber walls and be difficult to remove. Clean the chamber of the rifle thoroughly, then plug the bore immediately ahead of the throat with a small rag - but not so tightly it cannot be driven out. If possible, pour the molten Cerrosafe through a small tube into the bottom of the cast, gradually removing the tube as the chamber fills. If the barrel is cold, warm it to room temperature or above before making the cast. When cooled, remove from chamber, using a rod or dowel from the muzzle end of the gun.
SPECS: Sold by weight. Alloy. Infinitely reusable.
Newsletter